Bedienungsanleitung BEKO HNE 51210S (Seite 13 von 60) (Alle Sprachen)

761456

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

d. In case the thickness of the lateral wall units is 16mm,

put, with embedded fixing, the O (*) spacers at the sides

of the hood in correspondence with the holes used for the

passage of the fixing screws to the lateral wall units. Fig.

e. Hang the hood onto the hooks (*) and adjust the position

of the hood with headless screws S1 and adjusting the

position of the hooking brackets with screws S2. Fig. 7

f. Fix the hood to the lateral wall units with 4 screws P. Fig.

g. Mount the lower corner Q (*) to the hood with two screws

and plastic washers T. They will serve to cover possible

spaces between the rear of the hood and the wall. Fig. 7

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Use the keys or buttons envisaged for the control of the lights

and the power of the available suction.

Only in some models: switching on and off the fan that

adjusts the suction power and, in some cases, switching the

lights on and off, is controlled by opening and closing the

steam collector.

If your product is provided with an electrically or mechanically

activated valve, the keys and/or the buttons and/or the

handles available are for controlling the lights and for opening

and closing the valve.

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

WARNING: Failure to carry out the basic cleaning

recommendations of the cooker hood and replacement of the

filters may cause fire risks.

Therefore, we recommend observing these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Grease filter

Traps cooking grease particles.

If situated inside the support grill, it may be one of the

following types:

Paper filter must be replaced once a month or if colouring

appears on upper side, in such cases the colouring is evident

through the grill openings.

Sponge filter should be washed with hot soapy water once a

month and replaced every 5 to 6 washes.

Metallic filter must be cleaned once a month, with non

abrasive detergents, by hand or in dishwasher on low

temperature and short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To access fats filter V, open the suction grill with hooks H1 or

H2 (depending on the model in possession) and free it from

the W stops. Fig. 9

Some models are provided with anti-grease filter incorporated

in the suction grill, these should be removed from the housing

by pulling the handles H2 (Fig. 9) upwards and sliding out,

wash these filters as with metallic filters.

Charcoal filter (filter version only)

It absorbs unpleasant odours caused by cooking.

The saturation of the charcoal filter occurs after more or less

prolonged use, depending on the type of cooking and the

regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least

every four mounths (or when the filter saturation indication

system – if envisaged on the model in possession – indicates

this necessity).The charcoal filter may NOT be washed or

regenerated.

Cover the grill that protects the suction motor with the carbon

filter so that the slots on the filter correspond to the pins on the

sides of the motor protection grill.

Turn the carbon filter clockwise to block them (bayonet fixing).

Fig. 10

Proceed in reverse for mounting.

Note: 2 filters are needed in the models with 2 motors. The

system of montage and dismantling is identical.

Replacing lamps

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

Remove the suction gril to access the lamp area.

Remove the damaged lightbulb and replace with an oval

incandescent lightbulb max. 40W E14.

If the lights do not work, make sure that the lamps are fitted

properly into their housings before you call for technical

assistance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO HNE 51210S Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info