Bedienungsanleitung BEKO WMB 51221 C (Seite 58 von 76) (Deutsch, Englisch, Holländisch, Französisch)

676601

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

 Makesurethatthewaterinletanddischarge

hoses as well as the power cable are not

folded, pinched or crushed while pushing

the product into its place after installation or

cleaning procedures.

Appropriate installation location

• Placethemachineonarigidfloor.Donot

place it on a long pile rug or similar surfaces.

• Totalweightofthewashingmachineandthe

dryer-withfullload-whentheyareplaced

ontopofeachotherreachestoapprox.

180kilograms.Placetheproductonasolid

and flat floor that has sufficient load carrying

capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the

packaging reinforcement. Remove the packaging

reinforcement by pulling the ribbon.

Removing the transportation locks

Do not remove the transportation locks before

taking out the packaging reinforcement.

Remove the transportation safety bolts before

operating the washing machine, otherwise,

the product will be damaged.

1. Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Remove transportation safety bolts by turning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manualbagintotheholesontherearpanel.

(P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needs to be moved again in the future.

 Nevermovetheproductwithoutthe

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–1

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attachapressurereducingvalveifwater

pressure is higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

water valve before operating the product.

(Appliesfortheproductssuppliedwithablind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

thehotwatervalve.(Appliesfortheproducts

supplied with a blind stopper group.)

 Modelswithasinglewaterinletshouldnot

beconnectedtothehotwatertap.Insuch

a case the laundry will get damaged or the

product will switch to protection mode and will

not operate.

Do not use old or used water inlet hoses on

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connectthespecialhosessuppliedwiththe

product to the water inlets on the product.

Redhose(left)(max.90ºC)isforhotwater

inlet,bluehose(right)(max.25ºC)isforcold

water inlet.

Ensure that the cold and hot water

connections are made correctly when

installing the product. Otherwise, your laundry

will come out hot at the end of the washing

process and wear out.

2. Tightenallhosenutsbyhand.Neverusea

wrench when tightening the nuts.

3. Open the taps completely after making the

hose connection to check for water leaks at

theconnectionpoints.Ifanyleaksoccur,turn

off the tap and remove the nut. Retighten

the nut carefully after checking the seal. To

prevent water leakages and damages caused

by them, keep the taps closed when the

machine is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

Your house will be flooded if the hose comes

out of its housing during water discharge.

Moreover,thereisriskofscaldingdueto

high washing temperatures! To prevent such

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WMB 51221 C Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info