Bedienungsanleitung BEKO WMB71642 (Seite 8 von 40) (Englisch)

556825

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Keep the transportation safety bolts in

a safe place to reuse when the washing

machine needs to be moved again in the

future.

Never move the product without the

transportation safety bolts properly fixed

in place!

Connecting water supply

The water supply pressure required to run

the product is between 1 to 10 bars (0.1

– 10 MPa). It is necessary to have 10 – 80

liters of water flowing from the fully open

tap in one minute to have your machine

run smoothly. Attach a pressure reducing

valve if water pressure is higher.

If you are going to use the double water-

inlet product as a single (cold) water-inlet

unit, you must install the supplied stopper

to the hot water valve before operating

the product. (Applies for the products

supplied with a blind stopper group.)

If you want to use both water inlets of the

product, connect the hot water hose after

removing the stopper and gasket group

from the hot water valve. (Applies for the

products supplied with a blind stopper

group.)

Models with a single water inlet should

not be connected to the hot water tap. In

such a case the laundry will get damaged

or the product will switch to protection

mode and will not operate.

Do not use old or used water inlet hoses

on the new product. It may cause stains

on your laundry.

1. Connect the special hoses supplied with

the product to the water inlets on the

product. Red hose (left) (max. 90 ºC) is for

hot water inlet, blue hose (right) (max. 25

ºC) is for cold water inlet.

Ensure that the cold and hot water

connections are made correctly when

installing the product. Otherwise, your

laundry will come out hot at the end of

the washing process and wear out.

2. Tighten all hose nuts by hand. Never use

a wrench when tightening the nuts.

3. Open the taps completely after making

the hose connection to check for water

leaks at the connection points. If any

leaks occur, turn off the tap and remove

the nut. Retighten the nut carefully after

checking the seal. To prevent water

leakages and damages caused by them,

keep the taps closed when the machine

is not in use.

Connecting to the drain

• The end of the drain hose must be

directly connected to the wastewater

drain or to the washbasin.

Your house will be flooded if the

hose comes out of its housing during

water discharge. Moreover, there is

risk of scalding due to high washing

temperatures! To prevent such situations

and to ensure smooth water intake and

discharge of the machine, fix the end

of the discharge hose tightly so that it

cannot come out.

• The hose should be attached to a height

of at least 40 cm, and 100 cm at most.

• In case the hose is elevated after

laying it on the floor level or close to

the ground (less than 40 cm above the

ground), water discharge becomes more

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WMB71642 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info