757479
19
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Washing Machine / User Manual 19 / EN
To deactivate the Child Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds while any programme is running.
While you are holding for 3 seconds, the "Child Lock Enabled LED" will flash. You can release the
buttons when the LED turns off completely.
C
In addition to the method above, to deactivate the Child Lock, switch the Programme Selection knob to On / Off
position when no programme is running, and select another programme.
Child Lock is not deactivated after power failures or when the machine is unplugged.
4.3.12 Progress of programme
Progress of a running programme can be followed from the Programme Follow-up indicator. At
the beginning of every programme step, the relevant indicator light will turn on and light of the
completed step will turn off.
You can change the speed settings without stopping the programme flow while the programme is
running. To do this, the change you are going to make must be in a step after the running programme
step. If the change is not compatible, relevant lights will flash for 3 times.
C
If the machine does not proceed to the spinning step, the Rinse Hold function might be active or the automatic
unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the
machine.
4.3.13 Loadng door lock
There is a locking system on the loading door of the machine that prevents opening of the loading
door in cases when the water level is unsuitable.
Loading door light will start flashing when the machine is switched to Pause mode. The machine
checks the level of the water inside. If the level is suitable, the Loading Door light turns off and the
loading door can be opened within 1-2 minutes.
If the level is unsuitable, the Loading Door light remains on and the loading door cannot be opened.
If you are obliged to open the Loading Door while the Loading Door light is on, you must cancel the
current programme. See. "Cancelling the programme"
4.3.14 Changng the selectons after programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to pause mode while a programme is running.
The light of the step which the machine is in starts flashing in the Programme Follow-up indicator to
show that the machine has been switched to the pause mode.
Additionally, when the loading door is openable, the Loading Door light turns off completely.
Changing the speed settings
You can change the speed settings of the programme that is currently running. See "Speed
selection".
C
If no change is allowed, the relevant light will flash 3 times.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BEKO WTV6611BC1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BEKO WTV6611BC1

BEKO WTV6611BC1 Bedienungsanleitung - Holländisch, Französisch - 56 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info