Bedienungsanleitung BEKO WTV7712BLS1 (Seite 6 von 56) (Deutsch, Englisch)

757506

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

6 / EN Washing Machine / User Manual

4.1 Installation

• Apply to the nearest authorised service

agent for the installation of your product.

• Preparation of the location and electrical,

tap water and waste water installations at

the place of installation is under customer's

responsibility.

• Make sure that the water inlet and discharge

hoses as well as the power cable are not

folded, pinched or crushed while pushing

the product into its place after installation or

cleaning procedures.

• Make sure that the installation and electrical

connections of the product are performed

by authorised service. Manufacturer shall

not be held liable for damages that may

arise from procedures carried out by

unauthorised persons.

• Prior to installation, visually check if the

product has any defects on it. If so, do not

have it installed. Damaged products cause

risks for your safety.

4.1.1 Appropriate installation location

• Place the product on a hard and level floor.

Do not put it onto a carpet with high pile or

other similar surfaces.

• When the washing machine and dryer are

placed on top of each other, their total

weight –when loaded– amounts to 180 kg.

Place the product on a solid and flat floor

that has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product in the

environments where the temperature falls

below 0 ºC.

• Leaving a gap at the sides of the machine is

suggested to reduce vibration and noise

• On a graduated floor, do not place the

product next to the edge or on a platform.

• Do not place heat sources such as Hobs,

Irons, Ovens, etc. on the washing machine

and do not use them on the product.

4.1.2 Removing packaging reinforcement

Tilt the machine

backwards to remove the

packaging reinforcement.

Remove the packaging

reinforcement by pulling

the ribbon. Do not make

this operation alone by

yourself.

4.1.3 Removing the

transportation locks

1. Loosen all bolts with an appropriate wrench

until they turn freely.

2. Remove the transport safety bolts by

turning them slightly.

3. Insert the plastic covers in the bag

containing the user manual to the openings

on the rear panel.

CAUTION!

• Remove the transportation safety bolts

before operating the washing machine!

Otherwise, the product will be damaged.

INFORMATION

• Keep the transportation safety bolts in

a safe place to reuse when the washing

machine needs to be moved again in the

future.

• Install the transport safety bolts in reverse

order of the disassembly procedure.

• Never move the product without the

transportation safety bolts properly fixed in

place!

4.1.4 Connecting water supply

INFORMATION

• It is necessary to have 10 – 80 liters of

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

CAUTION!

• Models with a single water inlet should not

be connected to the hot water tap. In such

a case the laundry will get damaged or the

product will switch to protection mode and

will not operate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WTV7712BLS1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO WTV7712BLS1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info