3. Bringen Sie die Verteiler und Brennerdeckel auf den entspre-
chenden Kochstellen an und setzen Sie die Roste korrekt in
den entsprechenden Halteelementen ein.
B) Einstellung der Gashähne (Abb. 8):
1. Drehen Sie die Bedienknebel auf die niedrigste Stufe.
2. Ziehen Sie die Bedienknebel der Gashähne ab. Es wird eine
Knebeldichtung aus flexiblem Gummi sichtbar. Drücken Sie
diese mit der Schraubendreherspitze beiseite, um an die Ein-
stellschraube des Gashahns zu gelangen.
Bauen Sie die Knebeldichtungen niemals aus. Die Dichtun-
gen sind für den fehlerfreien Betrieb des Geräts unerlässlich,
da sie das Eindringen von Flüssigkeiten und Schmutz ins Ge-
räteinnere verhindern.
3. Stellen Sie die minimale Gaszufuhr ein, indem Sie die Bypass-
Schraube mit einem Schlitzschraubenzieher drehen.
Je nach Gasart, auf die Sie umstellen (siehe Tabelle III), müs-
sen entsprechende Schritte durchgeführt werden:
A: die Bypass-Schrauben ganz anziehen.
B: die Bypass-Schrauben bis zum korrekten Gasaustritt an den
Brennern lockern.
C: die Bypass-Schrauben müssen von einem autorisierten
Fachmann ausgetauscht werden.
D: nehmen Sie keine Veränderungen an den Bypass-Schrau-
ben vor.
Stellen Sie sicher, dass der Brenner bei einer Umstellung des
Bedienknebels von der höchsten auf die niedrigste Stufe nicht
ausgeht und nicht zurückschlägt.
Wenn Sie nicht an die Bypass-Schraube gelangen sollten,
bauen Sie die Fettauffangschale, die mit dem restlichen Koch-
feld mittels eines Clip-Befestigungssystems und Schrauben ver-
bunden ist, aus. Zum Abnehmen gehen Sie wie folgt vor:
1. Nehmen Sie alle Roste, Brennerdeckel, Verteiler und Bedien-
knebel ab.
2. Lockern Sie die Brenner-Schrauben.
3. Verwenden Sie ggf. den bei unserem Kundendienst erhältli-
chen Demontagehebel 483196. Lösen Sie die vordere Clip-Be-
festigung, indem Sie den Hebel in den markierten Bereichen
ansetzen. Abb. 9.
4. Für den Wiedereinbau des Geräts folgen Sie den Ausbauan-
weisungen in umgekehrter Reihenfolge.
Bauen Sie niemals die Achse des Gashahns aus (Abb. 10). Bei
einer Störung den kompletten Gashahn ersetzen.
en
Ú
Installation instructions
Safety precautions
Read the appliance's instructions before installing and using.
The images shown in these instructions are for guidance only.
The manufacturer is ex
requirements of this manual are not complied with.
This appliance must only be used in well ventilated places. It
must not be connected to a combustion product removal
device.
All operations relating to installation, connection, regulation
and conv
authorised installation engineer
regulations, standards and the specifications of the local gas
and electricity suppliers. Special attention shall be paid to
ventilation regulations.
It is recommended you contact the T
Service to change to another gas type.
This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be valid
if the appliance is used for the purpose for which it was
designed.
Before installing, you need to check that local distribution
conditions are compatible with the appliance's adjustment
indicated on the specifications plate (gas type and pressure,
power, voltage). See table I.
Before y
supply
The supply cable must be attached to the unit to prevent it from
touching hot parts of the oven or hob.
Appliances with electrical supply must be earthed.
Do not tamper with the appliance's interior. If necessary, call our
Technical Assistance Service.
Before installing
This appliance is class 3 type, according to the EN 30-1-1
regulation for gas appliances: built-in appliance.
The kitchen unit in which the appliance is installed must be
properly secured and stable.
The kitchen units next to the appliance, the laminated covering
and glue for adhering it must be made of non-flammable and
heat-resistant materials.
This appliance cannot be installed above fridges, washing
machines, dishwashers or similar.
An oven must have forced ventilation to install a hob above it.
Check the dimensions of the oven in the installation manual.
If an extractor fan is installed, you must follow the instructions in
the installation manual, always respecting the minimum vertical
distance from the hob (fig. 1).
Preparation of the kitchen unit (fig. 1-2)
Make an appropriate size cut in the work surface.
If the hob is electric or mixed (gas and electricity) and there is
no oven below, place a non-flammable separator (e.g. metal or
plywood) 10 mm from the bottom of the hob. This will prevent
access to the base of the hob.If the hob is gas, it is
recommendable to place the separator at the same distance.
On wood work surfaces, varnish the cutting surfaces with a
special glue. This protects them from moisture which could
collect under the work surface.
Installation of appliance
Depending on the model, the adhesive seal may be factory-
fitted. If this is the case, it should not be removed under any
circumstances, since the adhesive seal prevents leaks. If the
seal has not been factory-fitted, apply it to the underside of the
hob. Fig. 3.
Fitting the appliance onto the kitchen unit:
1. Screw each one of the clips into the position indicated so that
they are free to rotate.
2. Insert and centre the hob.
Press the sides of the hob until it is supported around its entire
perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work
surface is. Fig. 4.
Remo
Turn off the appliance's electricity and gas supply.
Unscrew the clips and proceed in the reverse order to
installation.
Gas connection (fig. 5)
The end of the inlet connection point of the gas hob has a 1/2”
(20.955 mm) thread that allows for:
■ fixed connection.
■ connection using a flexible metal pipe (L min. 1 m -
max. 3 m).
The watertight seal supplied or available from the technical
assistance service (code 034308) must be inserted between
the manifold outlet and the gas supply.
You must prevent the pipe from coming into contact with
moving parts of the kitchen unit (for example, a drawer) and
prevent access to any spaces which might become obstructed.
If you need to connect the gas supply horizontally, our technical
assistance service can supply you with an L-tube
(code 173018), and a seal (code 034308).
If you need to make a cylindrical connection, replace the factory-
fitted L-tube with the one in the accessory bag supplied or
available from the technical assistance service (code 529649).
Fig. 5a.
Please remember to insert the seal.
: Danger of leaks!
If any connection is handled, check the seal.
The manufacturer is not liable for any connection leaking, after
being handled.
Electric connection (fig. 6)
Check that the voltage and power of the appliance are
compatible with the electrical installation.
The hobs are supplied with a power cable with or without a wall
socket plug.
