Bedienungsanleitung Belion GK604ZB10 (Seite 10 von 28) (Englisch, Holländisch)

630725

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Replacing the burner nozzles

After having replaced the gas connecting piece on the

appliance to be converted to another gas type, all burner

nozzles must be replaced. The following steps must be

observed:

1. Turn off all switches on the control panel.

2. Shut off the gas supply.

3. Remove the pan support and burner parts.

4. Remove the burner nozzles (Allen key 7).

5. To identify the burner nozzles, see the table in the section

entitled "Technical properties - gas".

Insert the new nozzles in the corresponding burners.

Once the nozzles have been replaced, perform a leak test. See

the section entitled "Leak test".

Adjusting or replacing the bypass nozzles

The bypass nozzles regulate the minimum flame height of the

burners.

Preparation

Shut off the gas supply.

: Risk of electric shock!

Disconnect the appliance from the power supply.

1. Turn off the switches on the control panel.

2. Pull of all handles carefully upwards.

To adjust or replace the bypass nozzles when converting

from natural gas to liquid gas:

For models with two-hand spark ignition (with igniter)

(optional):

Fully close the bypass nozzles at the tap openings on the hob

plate.

The bypass nozzles of the burners can be adjusted via the tap

openings, which can be seen if the control knobs are pulled off

the control panel. To do this, use a flat head screwdriver (no. 2)

to fully screw in the bypass nozzles in the tap openings (make

sure that the cables are not damaged in the process).

For models with one-hand spark ignition (with automatic

igniter) (optional):

To reach the bypass nozzles, the hob plate must be removed.

To do this, read the section entitled "Removing the hob plate".

After the hob plate has been removed, the ignition group on the

gas taps must be removed.

The bypass nozzles must then be screwed in fully.

Then the ignition group must be refitted and the hob plate

installed as described in the section entitled "Installing the hob

plate".

To adjust or replace the bypass nozzles when converting

from natural gas to liquid gas:

For models with two-hand spark ignition (with igniter)

(optional):

All of the appliance's bypass nozzles must be replaced. To do

this, read the section entitled "Removing the hob plate".

The instructions in the section entitled "Replacing the bypass

nozzles" must then be followed.

Then, follow the instructions in the section entitled "Installing the

hop plate".

For models with one-hand spark ignition (with automatic

igniter) (optional):

All of the appliance's bypass nozzles must be replaced. To do

this, read the section entitled "Removing the hob plate".

After the hob plate has been removed, the ignition group

located on the gas taps must be removed. The instructions in

the section entitled "Replacing the bypass nozzles" must then

be followed.

Then reinstall the ignition group and follow the instructions in

the section entitled "Installing the hop plate".

6:



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Belion GK604ZB10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Belion GK604ZB10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info