Bedienungsanleitung Belion GK604ZB10 (Seite 12 von 28) (Englisch, Holländisch)

630725

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Leak test and function test

: Risk of explosion!

Avoid sparking. Do not use an open flame.

Perform the leak test only with a suitable leakage spray.

In the event of a gas leak

Shut off the gas supply.

Ensure that the room affected is well ventilated.

Check the gas and valve connections again. Repeat the leak

test.

The leak test must be performed by two people, in accordance

with the following instructions.

Check the gas connection

1. Open the gas supply.

2. Spray the gas connection with a leakage spray.

If small bubbles or foam form, indicating a gas leak, follow the

instructions in the section entitled "In the event of a gas leak".

Checking the burner nozzles

1. Open the gas supply.

Carry out the leak test separately for each nozzle.

2. Carefully close the hole in the burner nozzle to be checked

using your finger or a suitable device.

3. Spray the nozzle with a leakage spray.

4. Press the function selector and turn it anti-clockwise. This

supplies the nozzle with gas.

If small bubbles or foam form, indicating a gas leak, follow the

instructions in the section entitled "In the event of a gas leak".

Checking the bypass valves

1. Open the gas supply.

Carry out the leak test separately for each bypass screw.

2. Carefully close the hole in the burner nozzle to be checked

using your finger or a suitable device.

3. Spray the nozzle in the burner to be checked with a leakage

spray.

4. Push the control knob and turn it anti-clockwise. This supplies

the nozzle with gas.

If small bubbles or foam form, indicating a gas leak, follow the

instructions in the section entitled "In the event of a gas leak".

Correct flame formation

Burner

The flame behaviour and temperature development must be

checked for each burner after the appliance is converted to a

different gas type.

In the event of a problem, compare the nozzle values to the

values in the table.

Only for models without safety pilot

1. Ignite the hob burner as described in the operating

instructions.

2. Check the large and small flames for the correct flame

behaviour. The flame must burn evenly and continuously.

3. Using the burner knob, switch quickly between the large and

small frame. Repeat this process a few times. The gas flame

must not flicker or go out.

Only for models with safety pilot

1. Light the gas with the igniter knob as described in the

operating instructions.

2. Turn the burner to the small flame setting.

Check whether the ignition is activated by holding the knob in

the "small flame" position for approximately 1 minute.

3. Check the large and small flames for the correct flame

behaviour. The flame must burn evenly and continuously.

4. Using the burner knob, switch quickly between the large and

small frame. Repeat this process a few times. The gas flame

must not flicker or go out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Belion GK604ZB10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Belion GK604ZB10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info