Bedienungsanleitung Bellman CXE-25 (Seite 4 von 5) (Englisch)

515359

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

safety valve (7), you may have waited too long before opening steam valve, and you should begin steaming process

immediately, or turn off the on-off switch (6).

little steam may always escape from the safety valve during ether the brewing or steaming process. This is okay, and may

e due to condensation of water that turns to steam after building up on the safety valve. You must get to know your

machine so that you will be able to notice when anything happens that is out of the ordinary. If at any point it seems to you

that your machine is functioning strangely, turn the unit off, unplug it, release the pressure through the steam (4) or coffee

alve (3), and have the unit repaired.

Once the steam is ready, place the container of cold milk under the steam jet (5) and turn on the steam valve (4) slowly.

The tip of the jet should be just below the surface of the milk. Open the steam valve until you are getting a full force of

steam. The milk should look now like there is lot of swirling motion and bubbling going on.

t this point the steam and milk are being forced together, causing the milk to froth. You will see immediately that the

milk will begin to become thicker and thicker as it rises towards the top, filing up the pitcher. As it rises you should follow

it continually by pulling the pitcher up slowly so that the tip of the steam jets always just below the surface of the milk.

This process should double the quantity of milk.

When the milk is fully frothed, put the tip of the steam jet down into the center of the milk allowing it to heat up. The

sound as it heats will change becoming deeper and deeper, almost to a groaning sound. At this point close the steam valve

(4) before removing the pitcher, and pour the frothed milk over your espresso. DO NOT LET MILK BOIL. (If you use

sugar, add sugar to the milk before the steaming process.) After pouring 3-5 cups, the froth and the liquid will separate,

and only the liquid will pour out. To top the espresso off with a white cap of foam, just spoon out some foam and put it on

top of the espresso and milk. Make certain no milk has been drawn into the steam jet by blowing a small amount of steam

into an empty cup to clear the jet. (Failure to do this will result in milk deposits clogging up steam jet.)

Cappuccino is 1/2 to 2/3 of a cup of espresso coffee, balanced with frothed milk.

To keep coffee hot, do not put espresso into individual cups until milk is frothed

SPECIAL NOTES FOR STEAMING MILK

1. If milk is not foamy, you probably did not allow enough steam to build before beginning the steaming process. Allow an

extra minute longer than you did before and once again repeat the above steaming process.

2. If you get a few big bubbles, rather than many tiny ones, tap the container of milk on the counter or let it stand for a

coupe of minutes before adding to the espresso.

3. For best results, spoon hot foamy milk into the top of your cup of espresso and sprinkle with ground chocolate or

cinnamon. If you wish to add liqueurs, do so before adding the milk.

4. To use the machine for steam only (for instance for steaming chocolate milk, wine, cider, etc.), fill the tank about half

full of cold water and turn off both the coffee valve (3) and the steam valve (4). Wait about 6-9 minutes or until the steam

light goes off, for pressure to build. When there is a sufficient amount of steam, begin the steaming process you used for

steaming milk.

HAT TO DO IF

If you do not get the desired amount of cups (3, 6, or 9) be sure that you have filled the tank to the proper water level

mark.

If you are making less than 9 cups of coffee and your espresso does not taste as good, try using the full amount of water

and turn off the coffee valve when enough coffee has been espressed out (remember a demitasse cup is 2 to 2-1/2 oz).

If you want the coffee to come out hotter, just open the coffee valve 1/4 turn. This will slow down the flow and allow the

coffee heat to build. If steam starts coming out of safety valve, open the coffee valve completely. This should stop the

steam from being released from safety valve. If it does not, shut off the unit. NOTE: Remember that a little steam may

release from the safely valve due to condensation. Here again it is important to be familiar with the working of your

particular machine.

If the steam valve (4) and coffee valve (3) are both closed and a large amount of steam begins escaping from safety valve

(7), turn off unit and unplug. It may require being serviced.

If coffee leaks out around the lid, make sure you have tightened the lid securely. If the leak continues, shut off the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bellman CXE-25 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info