Bedienungsanleitung Belrobotics BM2000 Big Mow (Seite 69 von 78) (Englisch)

818966

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Chapter 9 Service and Maintenance

3. Check the battery voltage of battery. The battery level can be seen on the user interface

screen.

4. Start the robot and test it comes back normally to the charging station

9.1.2 Blade replacement

The frequency with which blades needs to be replaced depends on the robot type, its use

and the ground it is working on. Since the condition of the blades is essential for satisfactory

mowing it is recommended that you check this part of your robot each week after installation

and at the beginning of each new mowing season.

The pantograph allows the blade to follow the curves of the ground. If the pantograph is not

operating correctly, blades can become blunt or break. The pantograph should be checked

and cleaned regularly.

There are also a number of ways in which you can prolong the life of your cutting blades.

Do not cut long grass in a single pass. This can blunt the blade edge prematurely. It is

advised to set the cutting height to 5 mm or 10 mm less than the height of the grass and to

proceed in several passes. This is particularly important during the first mows of the season.

Make sure the terrain is even. If the terrain has severe bumps or dips in it, the cutting head

may not be able to follow the contours of the terrain and blades my hit the ground. Try to even

out the terrain and if necessary exclude very uneven patches from the mowing area.

Furrows may appear near the charging station. It is therefore recommended to level the

ground near the station or lay artificial turf.

Remove molehills. When the robots hits a molehill, the blades slow down or may stop. Once

past the molehill, the blade returns to a normal speed. The resistance of the earth and the

changes in speed might loosen the screws (or damage the screw hole).

Avoid bare patches. The presence of bare patches within a grassy zone will cause the

rotational speed to change. If this speed shift occurs too often it may damage the pivot and

the screw hole. To avoid this problem you can raise the cutting height so that the robot is

cutting less grass and speed differences are diminished. Alternatively the bare patches can

be re-seeded.

Avoid contact with nylon ground marker. These can cause bluntness. It is recommended

to lower them below your cutting height.

Avoid low solid obstacles in the grass. These include sprinklers, stones, roots... Stones

and other moveable objects should be removed. To avoid permanent solid objects such as

sprinklers, set the cutting height to be higher than the obstacle, or adapt the mowing area to

avoid them.

Removable goals are another example of a solid obstacle which can not be detected by the

robot. Make sure they are removed before the mowing is scheduled.

Remove tall weeds near the peripheral wire. Tough tall plants can blunt or damage the

bladeIt is therefore preferable to keep clear the areas around your peripheral cables.

Big mow BM2000 User's Manual Version: Release 4.5.0 Last updated: 2022-08-20 69

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Belrobotics BM2000 Big Mow Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info