Bedienungsanleitung Benekov R100 (Seite 23 von 32) (Englisch)

693645

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

starting any work on the boiler, check that it is disconnected from the electrical power (the

plug is pulled out of the socket).

8.) As the function of the ventilator can result in a slight overpressure in the burner area, keep in mind

that the boiler must be tightly closed (fire door, upper cover, cleaning gap of the feeder, container

cover etc.).

9.) If the boiler is equipped with the fire extinguisher with paraffin plug, make a visual check of the

emergency extinguishing system from time to time and refill water if necessary.

10.) If the boiler is equipped with the fire extinguishing system with the thermostatic valve and

pressure bottle, and if an emergency situation occurs (longer power failure etc.) and the fuel in the

fuel container starts burning, the increased temperature will cause the thermostatic valve to open

and the fire will be extinguished with water from the water supply system or from the installed water

pressure tank.

Before the boiler is put into operation again, it is necessary to remove wet fuel, fill the water pressure

bottle and heat the boiler as described in 7.1.

If the water pressure tank is a part of the emergency extinguishing system, the air pressure in the

tank must be checked at least once a year. To this end, remove the cap of the valve at the tank and

using a common manometer, check the pressure. If the pressure is not sufficient, adjust it to 0,5 bar

with an air pump or a compressor.

11.) The worm feeder drive gear and the turniket drive gear are filled with synthetic oil from the

production and further maintenance is not required.

9. Troubleshooting

If problems with operation of the boiler appear, try one of the following solutions:

SYMPTOM REASON SOLUTION

The boiler is not connected

to the network.

Connect the boiler to the electrical power

network (230V/50Hz) with appropriate

cable with plug.

The display shows no

data.

Malfunction of the boiler

controller.

Change the controller for a new one.*

The cable of the engine is

disconnected / damaged.

Connect the engine / change the cable to

the engine.*

The engine is damaged. Change the engine.*

The worm feeder

doesn’t work.

The engine was overheated

and the thermal protection

was activated.

Let the engine cool down, after cooling the

engine will start again.

The worm feeder is blocked

(stone, etc.)

Dismantle the worm feeder and remove

the problem. Re-assemble the device.*

The thermal

protection of the

engine was activated

repeatedly.

In the fuel there is a great

amount of dust.

Remove the inappropriate fuel from the

boiler; fill the container with the specified

fuel.

The boiler drive is

working, but the

worm feeder doesn’t

work

The elastic pin between the

worm feeder and the drive

rod was cut.

Remove the rest of the broken pin and

install a new one (8x45, ISO 8752).

The worm gear is

moving but the fuel is

not being transported

There is no fuel in the

container.

Fill the container with recommended fuel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benekov R100 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info