Bedienungsanleitung Benning MM 1 (Seite 16 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

577325

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

09/ 2013

BENNING MM 1



2. Safety note

The instrument is built and tested in accordance with

DIN VDE 0411 part 1/ EN 61010-1

and has left the factory in perfectly safe technical condition.

To maintain this condition and ensure safe operation of the multimeter, the user

must observe the notes and warnings given in these instructions at all times.



The unit may be used only in power circuits within the overvolt-

age category III with a conductor for 600 V max. to earth.

Only use suitable measuring leads for this. With measurements

within measurement category III, the projecting conductive

part of a contact tip of the measuring leads must not be longer

than 4 mm.

Prior to carrying out measurements within measurement cat-

egory III, the push-on caps provided with the set and marked

with CAT III and CAT IV must be pushed onto the contact tips.

The purpose of this measure is user protection.

Remember that work on electrical components of all kinds is

dangerous. Even low voltages of 30 V AC and 60 V DC may be

dangerous to human life.



Before starting the multimeter up, always check it as well as all

cables and wires for signs of damage.

Should it appear that safe operation of the multimeter is no longer possible, it

should be shut down immediately and secured to prevent it being switched on

accidentally.

It may be assumed that safe operation is no longer possible:

- if the instrument or the measuring leads show visible signs of damage, or

- if the multimeter no longer functions, or

- after long periods of storage under unfavourable conditions, or

- after being subjected to rough transport.



In order to avoid danger,

- do not touch the bare prod tips of the measuring leads,

- insert the measurement leads in the appropriately

designated measuring sockets on the multimeter

3. Scope of delivery

The following items are included in the delivery of a BENNING MM 1:

3.1 one BENNING MM 1

3.2 one safety test lead, red (L= 1.4 m)

3.3 one safety test lead, black (L= 1.4 m)

3.4 one protective rubber holster

3.5 one compact protective carrying case

3.6 two 1.5 V micro batteries (built into unit)

3.7 one operating manual

Note on replaceable parts:

The BENNING MM 1 is powered by two 1.5 V micro batteries (2x1.5-V-IEC LR03).

4. Tester description

refer to figure 1: front tester panel

The display and operating elements shown in figure 1 are denoted as follows:

 Digital display for measurement values, display for bar graph, display for

overrange indication,

 Polarity display,

 Battery indicator, appears when the battery is low,

 Rotary switch for function selection

 Input terminal (positive

) for V, , µA, ,

 COM-Terminal, common return terminal for voltage and resistance

measure ments, continuity and diode tests,

 RANGE button,

 HOLD button,

 Protective rubber holster

) the automatic polarity display for direct and alternating current refers to this terminal

5. General Specifications

5.1 General specifications for the BENNING MM 1

5.1.1 The digital display is a 3½ digit liquid crystal display with 10,5 mm digit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM 1 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info