Bedienungsanleitung Benning MM 4 (Seite 16 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

577333

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

09/ 2013

BENNING MM 4



2. Safety notes

The instrument is built and tested in accordance with

DIN VDE 0411 part 1/ EN 61010-1

and has left the factory in perfectly safe technical condition.

To maintain this condition and ensure safe operation of the multimeter, the user

must observe the notes and warnings given in these instructions at all times.



The unit may be used only in power circuits within the over-

voltage category II with a conductor for 600 V max. to earth,

or within overvoltage category III with a conductor for 300 V

against ground.

Remember that work on electrical components of all kinds is

dangerous. Even low voltages of 30 V AC and 60 V DC may be

dangerous to human life.



Before starting the multimeter up, always check it as well as all

cables and wires for signs of damage.

Should it appear that safe operation of the multimeter is no longer possible, it

should be shut down immediately and secured to prevent it being switched on

accidentally.

It may be assumed that safe operation is no longer possible:

- if the instrument or the measuring leads show visible signs of damage, or

- if the multimeter no longer functions, or

- after long periods of storage under unfavourable conditions, or

- after being subjected to rough transport.



In order to avoid danger,

- do not touch the bare prod tips of the measuring leads,

- insert the measurement leads in the appropriately desig-

nated measuring sockets on the multimeter

3. Scope of supply

The following items make up the standard BENNING MM 4 package:

3.1 one Multimeter,

3.2 one current transducer clamp,

3.3 one safety test lead, black (length = 1.4 m, tip Ø 4 mm) with safety

caps,

3.4 two test probes, red (tip Ø 4 mm),

3.5 one compact protection case,

3.6 two 1.5 V micro-batteries (in place in Multimeter on delivery),

3.7 the set Operating Instructions.

Note on consumable parts:

The BENNING MM 4 is supplied by two 1.5 V batteries (2 x 1,5-V-IEC LR 03).

4. Description of unit

The BENNING MM 4 consists of two functional units:

- the Multimeter and

- the current transducer clamp.

See fig.1: Front panel of unit

The operating and indicating elements shown in fig. 1 are as follows:

1 Housing

2 Sliding switch for selecting the desired functions.

- Aus (OFF)

- Measurement of alternating voltage (AC) and direct voltage (DC).

These functions alternate with one-another when the function button

with the blue marking is pressed. When pressed longer (2 sec.) meas-

urement of alternating current, etc. The digital display 3 indicates the

function currently in effect.

- Resistance measurement, continuity test with buzzer and diode

test. These functions alternate with one-another when the function

button with the blue marking is pressed. The digital display 3 indicates

the function currently in effect.

3 Digital display (liquid-crystal principle). The following are indicated:

- the measurement value with the max. indication 4200,

- the polarity indication,

- the decimal point,

- the symbol for discharged battery,

- the type of voltage selected (DC or AC voltage),

- the measurement value held (hold function),

- the deviation from a measurement value stored in the unit memory

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM 4 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info