Bedienungsanleitung Benning MM 5-2 (Seite 20 von 134) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

692213

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

10/ 2015

BENNING MM 5-1/ 5-2



Note on optional accessory:

- Temperature probe (K-type) made of V4A tube

application: insertion probe for soft-plastic materials, liquids, gas and air

measuring range: - 196 °C up to 800 °C

dimensions: length = 210 mm, tube length = 120 mm, tube diameter =

3 mm, V4A (P.no. 044121)

Note on replaceable parts:

- The BENNING MM 5-2 contains fuses for overload protection:

One fuse rated 15 A rapid-acting (600 V) 50 kA, D = 10.3 mm, L = 38.1 mm

(P.no. 10149447).

- The BENNING MM 5-1/ MM 5-2 is supplied by means of two integrated

1.5 V micro (AAA) batteries (IEC LR 03).

- The above mentioned safety cable (tested spare part) are approved in

accordance with CAT III 1000 V/ CAT IV 600 V and for a current up 10 A.

4. Description of unit

See fig. 1: Front panel

The display and operating elements shown in fig. 1 are as follows:



Digital display, for the measurement reading and display for overrange

indication,



Polarity display,



Battery display,



Function key (blue),



VoltSensor key, for determining AC voltage to earth,



Δ/PEAK key, relative value function and peak value storage



Smart HOLD key,

Button (yellow), display illumination,



Rotating switch, for selecting measuring function.



Socket (positive

) for V, Ω, , Hz (+) (BENNING MM 5-1) or for V, Ω, ,

Hz, μA, , (BENNING MM 5-2)



COM socket, joint socket for measurement of current, voltage, resistance,

frequency, temperature, capacity, continuity and diode testing,



Socket (positive), for 10-A range, for currents up to 10 A



Protective rubber holster



LED (red) for voltage indicator

) The automatic polarity display for DC current and voltage refers to this.

5. General data

5.1 General data on multimeter

5.1.1 The digital display

is designed as a 4 digit liquid-crystal indicator with 16

mm digit height and decimal point. The highest value displayed is 6000.

5.1.2 The polarity indication



functions automatically. Only a polarity con-

trary to the socket definition is indicated, as “-”.

5.1.3 The range overload will be displayed with “OL” or “-OL” and sometimes

with an acoustic signal.

Attention: no display or warning by complete overload.

5.1.4 The rotary switch

is intended for selecting the measuring function.

The measuring range is selected automatically.

5.1.5 Volt sensor key

: The voltage indicator function is intended for local-

izing AC voltages to earth (see 8.9).

5.1.6 Press the Δ/PEAK key

(relative value function) to store the currently

displayed value and to display the difference (offset) between the stored

measured value and the following measured values. Press the Δ/PEAK

key

for 2 seconds to switch over to the “PEAK” function (peak value

storage). The “PEAK” function detects and stores the positive and

negative peak/ crest value (> 1 ms) in the mV, V AC/ DC and mA, A

AC/ DC function. Press the key to call up Pmax, Pmin and the currently

measured value (Pmax, Pmin). Press the key for approx. 2 seconds to

switch the device back to normal operating mode.

5.1.7 “Smart HOLD” - storage of measurement reading: When the “Smart HOLD”

key  is pressed, the measurement reading is stored in the memory.

The symbol “HOLD” appears in the display

at the same time. If the

measured value increases by 50 digit above the saved value the change

in measured value is shown by a blinking display and by a signal tone.

(changes of measured values between AC and DC voltage/ current will

not be recognized).

5.1.8 Press the yellow key

to activate the display illumination. The device is

switched off automatically after 2 seconds or by pressing the key again.

Deactivate the automatic switch-off by pressing the key (yellow)

and

simultaneously switching the BENNING MM 5-2 ON from the switch

position “OFF”.

5.1.9 The function key (blue)

serves to select the secondary or third func-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM 5-2 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info