Bedienungsanleitung Benning MM6.2 (Seite 21 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

692253

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

02/ 2016

BENNING MM 6-1/ 6-2



2. Safety notes

The instrument is built and tested in accordance with

DIN VDE 0411 part 1/EN 61010-1

DIN VDE 0411 part 2-033/EN 61010-2-033

DIN VDE 0411 part 031/EN 61010-031

and has left the factory in perfectly safe technical condition.

To maintain this condition and to ensure safe operation of the multimeter, the

user must observe the notes and warnings given in these instructions at all times.

Improper handling and non-observance of the warnings might involve severe

injuries or danger to life.



WARNING! Be extremely careful when working with bare con-

ductors or main line carrier! Contact with live conductors will

cause an electric shock!



The BENNING MM 6-1/ MM 6-2 may be used only in electrical

circuits of over voltage category III with a maximum voltage of

1000 V or of over voltage category IV with a maximum voltage

of 600 V between the conductor and ground.

Only use suitable measuring leads for this. With measurements

within measurement category III or measurement category IV,

the projecting conductive part of a contact tip of the measuring

leads must not be longer than 4 mm.

Prior to carrying out measurements within measurement cat-

egory III and measurement category IV, the push-on caps

provided with the set and marked with CAT III and CAT IV must

be pushed onto the contact tips. The purpose of this measure

is user protection.

Remember that work on electrical components of all kinds is

dangerous. Even low-voltages of 30 V AC and 60 V DC may be

dangerous to human life.



Before starting the multimeter, always check it as well as all

measuring leads and wires for signs of damage.

Should it appear that safe operation of the multimeter is no longer possible, it

should be shut down immediately and secured to prevent that it is switched on

accidentally.

It may be assumed that safe operation is no longer possible:

- if the instrument or the measuring leads show visible signs of damage, or

- if the multimeter no longer works, or

- after long periods of storage under unfavourable conditions, or

- after being subject to rough transportation, or

- if the device or the measuring leads are exposed to moisture, or



In order to avoid danger,

- do not touch the bare probe tips of the measuring leads

measuring leads,

- insert the measurement leads in the appropriately

designated measuring sockets on the multimeter



Cleaning:

Regularly wipe the housing by means of a dry cloth and

cleaning agent. Do not use any polishing agents or solvents!

3. Scope of delivery

The following items make up the standard BENNING MM 6-1/ MM 6-2 package:

3.1 one BENNING MM 6-1/ MM 6-2,

3.2 one safety measuring lead, red (L = 1.4 m),

3.3 one safety measuring lead, black (L = 1.4 m),

3.4 one wire temperature sensor, type K (only BENNING MM 6-1)

3.5 one protective rubber holster with magnetic holder,

3.6 one compact protection carrying case,

3.8 one 9 V block battery is integrated into the device,

3.9 one fuse for initial assembly is integrated into the device

(BENNING MM 6-2),

3.9

one operating manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM6.2 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info