Bedienungsanleitung Benning ST 725 (Seite 31 von 71) (Deutsch, Englisch, Französisch)

577356

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

01/ 2015

BENNING ST 725



The following symbols are used in these operating instructions and on the BENNING ST 725:



Warning of electrical danger!

Indicates instructions which must be followed to avoid danger to persons.



Important, comply with the documentation!

The symbol indicates that the information provided in the operating instructions must

be complied with in order to avoid risks.

This symbol on the BENNING ST 725 means that the BENNING ST 725 complies

with the EU directives.

This symbol appears on the display to indicate discharged batteries. As soon as the

battery symbol ashes, immediately replacethe batteries by new ones.Charged

batteries are also required for measuring in mains operating mode.



(AC) Alternating voltage or current.

Ground (Voltage against ground).



Protection class I



Protection class II

2. Safety note

The instrument is built and tested in accordance with

DIN VDE 0404-1 and -2

DIN EN 61010-1 (VDE 0411-1)

DIN EN 61010-2-030 (VDE 0411-2-030)

DIN EN 61557-1, -2, -4 and -10 (VDE 0413-1, -2, -4 and -10)

and has left the factory in perfectly safe technical state. To maintain this state and ensure safe

operation of the appliance tester, the user must observe the notes and warnings given in these

instructions at all times. Improper handling and non observance of the warnings might involve

severe injuries or danger to life.



WARNING! Be careful when working with bare conductors or main line carrier!

Contact with live conductors will cause an electric shock!



The BENNING ST 725 may be used only in power circuits within the overvoltage

category II with a conductor for 300 V AC max. to earth.

Remember that work on electrical components of all kinds is dangerous. Even

low voltages of 30 V AC and 60 V DC may be dangerous to human life.



The device must be connected to a single-phase mains with 230 V, 50 Hz,

pre-fuse 16 A only. Please make sure not to exceed the maximum breaking

capacity/ lamp load of the test socket of the BENNING ST 725 (see chapters 7.4

and 7.5). Exceeding the values might cause tripping of the fuses and damaging

of the BENNING ST 725. Damages due to overload are excluded from possible

warranty claims.



Do not carry out repeated protective conductor or contact current

measurements with a measuring duration of 2 x 5 minutes at test objects with

high current consumption (16 A). Repeated measurements at maximum load

(16 A) might heat up the inside of the device and thus also its surface.



The protective conductor resistance measurement might be distorted by

impedances connected in parallel of additional operating circuits and by

transient currents.

Measurements of the protective conductor resistance and of the insulating

resistance must be carried out at idle system parts only.



Before starting the appliance tester up, always check it for signs of damage.

Should it appear that safe operation of the appliance tester is no longer possible, it should be

shut down immediately and secured to prevent it being switched on accidentally.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning ST 725 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info