Bedienungsanleitung Benning ST 725 (Seite 45 von 71) (Deutsch, Englisch, Französisch)

577356

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

01/ 2015

BENNING ST 725





Before testing an RCD, the 4 mm safety plug of the test cable must be

disconnected from the test socket

Measurement might be influenced by:

- a possibly existing voltage between the protective conductor of the

shockproof socket and earth

- leakage currents in the circuit behind the RCD

- further earthing equipment

- equipment which is connected behind the RCD and which will cause a

longer tripping time, e.g. capacitors or rotating machines

9.5.1 Testing of permanently installed RCDs

- Connect the IEC power cord to the IEC connector J of the BENNING ST 725.

- Connect the shock-proof plug to a shock-proof socket which is protected by the RCD to be

tested and switch on the RCD.

- Press the -key

to start the RCD test.

- If the "rESET" symbol is still shown on the display and the "LN" and "LE" symbols are

flashing, turn the shock-proof plug in the shock-proof socket by 180° and press the -key

again to start the test.

- Whenever the "rESEt" symbol appears on the display, switch the RCD on again.

- The BENNING ST 725 generates a fault current of 30 mA with positive (0°) or negative

(180°) initial polarity. The RCD trips and the tripping times of the one-fold nominal fault

current are measured.

- If the tripping time is less than the limiting value (200 ms), a will be shown next to the

tripping time.

- Subsequently, the BENNING ST 725 generates a fault current of 150 mA with positive (0°) or

negative (180°) initial polarity. The RCD trips and the tripping times of the five-fold nominal

fault current are measured.

- If the tripping time is less than the limiting value (40 ms), a will be shown next to the

tripping time.

- The test is considered to be passed, if "PASS" is shown on the display.

Seegure8a: TestingofpermanentlyinstalledRCDs(I

ΔN

=30mA)

Note:

- By generating a fault current of 30 mA, it is proven that the RCD will trip when the nominal

fault current is reached. If the limiting value of the maximum contact voltage of 50 V is

exceeded, the "UB > 50 V" symbol will be shown on the display and the testing will be

stopped.



Measurement might be influenced by:

- a possibly existing voltage between the protective conductor of the

shockproof socket and earth

- leakage currents in the circuit behind the RCD

- further earthing equipment

- equipment which is connected behind the RCD and which will cause a

longer tripping time, e.g. capacitors or rotating machines

9.5.2 Testing of portable RCDs (PRCDs)

- Connect the plug of the mains connection cable to the jack K of the BENNING ST 725.

- Connect the shock-proof plug to a 230 V shock-proof socket. With the mains voltage being

applied, the voltage measurement will start automatically.

- Depending on the external conductor position (right or left) of the shock-proof socket, the

voltage potentials between the connecting terminals L, N and PE will be shown on the

display for approx. 2 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning ST 725 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info