Bedienungsanleitung Benning ST 725 (Seite 46 von 71) (Deutsch, Englisch, Französisch)

577356

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

01/ 2015

BENNING ST 725



- Connect the portable RCD (PRCD) to the test socket

of the BENNING ST 725.

- Connect the IEC power cord included in the scope of delivery to the IEC connector J of the

BENNING ST 725 and connect the shock-proof plug to the portable RCD (PRCD) as shown

in figure 7b. The cable outlet must point towards the display!

- Press the -key

to switch the mains voltage to the test socket

. The "rCd" and "rESEt"

symbols are shown on the display.

- Switch the portable RCD (PRCD) on.

- If the "rESET" symbol is still shown on the display and the "LN" and "LE" symbols are

flashing, please verify whether the portable RCD (PRCD) is switched on. If it is switched on,

turn the shock-proof plug of the IEC power cord in the portable RCD (PRCD) by 180° and

start the test again.

Whenever the "rESEt" symbol appears on the display, switch the portable RCD (PRCD) on again.

- The BENNING ST 725 generates a fault current of 30 mA with positive (0°) or negative

(180°) initial polarity. The portable RCD (PRCD) trips and the tripping times of the one-fold

nominal fault current are measured.

- If the tripping time is less than the limiting value (200 ms), a will be shown next to the

tripping time.

- Subsequently, the BENNING ST 725 generates a fault current of 150 mA with positive (0°) or

negative (180°) initial polarity. The portable RCD (PRCD) trips and the tripping times of the

five-fold nominal fault current are measured.

- If the tripping time is less than the limiting value (40 ms), a will be shown next to the

tripping time.

- The test is considered to be passed, if "PASS" is shown on the display.

Note:

Some portable PRCD types (e.g. PRCD-S, PRCD-K) switch off L, N and PE on all poles so that

the BENNING ST 725 does not detect any connection between the IEC connector J and the

test socket

. Testing of these PRCD types must be carried out according to chapter 9.5.1 "Test-

ing of permanently installed RCDs" by connecting the portable RCD (PRCD) to a mains socket

which is not protected by another RCD.

Seegure8b: TestingofportablePRCDs(I

ΔN

=30mA)

10. Measured value memory

The BENNING ST 725 is equipped with a measured value memory to store the measured values

of 999 test objects.

10.1 Storing measured values

- As soon as the test sequence is completed and the test result is available, press the -key

 to store the displayed measured values to the first free storage location. The storage will

be confirmed by the "STORE" symbol and the storage location number shown on the display

. The -key  will be blocked until another test is carried out in order to prevent double

storage. With each new storage, the storage location number will be increased automatically

by one storage location. As soon as all 999 storage locations are occupied, the "FULL"

symbol will be shown on the display

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning ST 725 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info