577368

Benning ST 750A Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
08/ 2012 10 / 58
BENNING ST 750 A
7.2 Limiting Values
If desired, the factory settings of the limiting values can be changed. The setting will remain valid
until mains switch-off! For each restart, the BENNING ST 750 A Appliance Tester will be reset to
the factory settings! The factory settings of the limiting values comply with the applicable VDE regu-
lationsandcanbetakenfromchapter20.2"FactorySettings,Setup,LimitingValues".Settingcan
be done from each start menu and from each measuring type menu. For this purpose, successively
select the following: <Setup> / <Limiting Values>.
Select the desired tab, select the value and press <Input> (display input key-
board opens). Delete and correct the old value by means of the <Clear> or <<-->.
Inthe"LimitingValuesSetup"menu,thedeviatingvaluewillbehighlightedinredcolour.Returnto
the start menu by pressing <Next> / <Save> / <Yes> / <Back>.
RPE data (resistance measurement of the PE conductor):
RPE VDE 701-702 = resistance for a cable length of 5 m and 1.5mm²
RPE VDE 751 = resistance for a cable length of 5 m and 1.5mm²
RPE per 7.5 m line length = additional resistance per 7.5 m line length
Line length = total length of the device supply line
Cross-section = cross-sectional area of the device supply line
RInsu data (insulation measurement):
RInsu-1 VDE 701-702 = insulating resistance of primary to PE
RInsu-1 VDE 701-702 heating elements = insulating resistance of primary to PE
RInsu-2 / RInsu-3 VDE 701-702 = insulating resistance of secondary to PE / primary to secondary
RInsu-1 VDE 701-702 Ua (SELV/PELV) = insulating resistance of primary to PE (SELV devices)
RInsu-1 VDE 751 = insulating resistance primary to PE
RInsu-2 VDE 751 = insulating resistance of secondary to PE
RInsu-3 VDE 751 = insulating resistance of primary to applied part
Testing voltage for primary to PE = testing voltage for primary to PE
Testing voltage for secondary to PE = testing voltage for secondary to PE
Testing voltage for primary to secondary = testing voltage for primary to secondary
IAL data (alternative leakage current measurement):
IPE VDE 701-702 protection class I = PE alternative leakage current
ILeak VDE 701-702 protection class II = alternative leakage current of accessible parts
ILeak VDE 751 protection class I = PE alternative leakage current
ILeak VDE 751 protection class I = alternative leakage current of accessible parts
Patient leakage current BF = alternative patient leakage current of applied part, type BF
Patient leakage current CF = alternative patient leakage current of applied part, type CF
ILeak data (leakage current measurement):
IPE VDE 701-702 protection class I = PE leakage current
ILeak VDE 701-702 protection class II = leakage current of accessible parts
ILeak VDE 751 protection class I = PE leakage current
ILeak VDE 751 protection class I = leakage current of accessible parts
Patient leakage current BF = patient leakage current of applied part, type BF
Patient leakage current CF = patient leakage current of applied part, type CF
ICont data (contact current measurement):
ICont VDE 701-702 = contact current to PE
Functional data (functional measurement):
IPE VDE 701-702 = PE leakage current (differential current measurement)
ICont VDE 701-702 = contact current to PE (differential current measurement)
IPE VDE 751 = PE leakage current (differential current measurement)
ICont VDE 751 = contact current to PE (differential current measurement)
Ua data (measurement on PELV / SELV devices):
Max. output voltage = max. output voltage for PELV / SELV devices
Cable data (cable measurement):
Line length = simple line length
Cross-section = cross-sectional area of the conductor
Conductor qty. = conductor quantity (for total length)
7.3 System Settings
Select <Setup> / <System Settings> to modify and permanently save the baud rate, parity, data
bits and stop bits e.g. for barcode scanners, RFID readers, PCs and printers.
08/ 2010 10 / 58
BENNING ST 750
RPE data (resistance measurement of the PE conductor):
RPE VDE 701-702 = resistance for a cable length of 5 m and 1.5mm²
RPE VDE 751 = resistance for a cable length of 5 m and 1.5mm²
RPE per 7.5 m line length = additional resistance per 7.5 m line length
Line length = total length of the device supply line
Cross-section = cross-sectional area of the device supply line
RInsu data (insulation measurement):
RInsu-1 VDE 701-702 = insulating resistance of primary to PE
RInsu-1 VDE 701-702 heating elements = insulating resistance of primary to PE
RInsu-2 / RInsu-3 VDE 701-702 = insulating resistance of secondary to PE / primary to secondary
RInsu-1 VDE 701-702 Ua (SELV/PELV) = insulating resistance of primary to PE (SELV devices)
RInsu-1 VDE 751 = insulating resistance primary to PE
RInsu-2 VDE 751 = insulating resistance of secondary to PE
RInsu-3 VDE 751 = insulating resistance of primary to applied part
Testing voltage for primary to PE = testing voltage for primary to PE
Testing voltage for secondary to PE = testing voltage for secondary to PE
Testing voltage for primary to secondary = testing voltage for primary to secondary
IAL data (alternative leakage current measurement):
IPE VDE 701-702 protection class I = PE alternative leakage current
ILeak VDE 701-702 protection class II = alternative leakage current of accessible parts
ILeak VDE 751 protection class I = PE alternative leakage current
ILeak VDE 751 protection class I = alternative leakage current of accessible parts
Patient leakage current BF = alternative patient leakage current of applied part, type BF
Patient leakage current CF = alternative patient leakage current of applied part, type CF
ILeak data (leakage current measurement):
IPE VDE 701-702 protection class I = PE leakage current
ILeak VDE 701-702 protection class II = leakage current of accessible parts
ILeak VDE 751 protection class I = PE leakage current
ILeak VDE 751 protection class I = leakage current of accessible parts
Patient leakage current BF = patient leakage current of applied part, type BF
Patient leakage current CF = patient leakage current of applied part, type CF
ICont data (contact current measurement):
ICont VDE 701-702 = contact current to PE
Functional data (functional measurement):
IPE VDE 701-702 = PE leakage current (differential current measurement)
ICont VDE 701-702 = contact current to PE (differential current measurement)
IPE VDE 751 = PE leakage current (differential current measurement)
ICont VDE 751 = contact current to PE (differential current measurement)
Ua data (measurement on PELV / SELV devices):
Max. output voltage = max. output voltage for PELV / SELV devices
Cable data (cable measurement):
Line length = simple line length
Cross-section = cross-sectional area of the conductor
Conductor qty. = conductor quantity (for total length)
7.2 System Settings
Select <Setup> / <System Settings> to modify and permanently save the baud rate, parity, data
bits and stop bits e.g. for barcode scanners, RFID readers, PCs and printers.
see chapter 16 to 18
<Barcode Scanner>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
<RFID Reader>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
<PC>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
<Printer>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
7.2.1 System Data
The device version and serial number are listed under <Setup> / <System Settings> /
<System Data>. The duration of the individual test procedures (standard = 5 sec.) is determined by
the test time. The safety shut-off terminates a test procedure (standard = 30 sec.).
Thecontactsurfacesbetweenconnectorshaveonlylowtransitionresistances.Todenethetransi-
tionresistance,herethe assumable resistance value is entered (standard = 1Ω). Moreover,itis
denedwhetheraprinterorabarcodescannerisconnectedtotheserialinterface.
Mains pole reversal ON: On the test socket, L and N are interchanged.
see chapter 16 to 18
<Barcode Scanner>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
<RFID Reader>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
<PC>
Thefollowingeldsarereleasedfortheuser:
- setting of baud rate, parity, data bits and stop bits
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Benning ST 750A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Benning ST 750A

Benning ST 750A Bedienungsanleitung - Deutsch - 68 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info