Bedienungsanleitung Benning ST 750A (Seite 38 von 58) (Englisch)

577368

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

08/ 2012 38 / 58



BENNING ST 750 A

12. Carrying out the Integrated Automatic Test

Test samples already existing in a database can be tested rapidly by means of the automatic test.

The sequence described here applies to an already existing database (name), customer (name)

with registered test samples (ID no.). After pressing <Automatic Test> in the start menu, select the

following in the menu displayed:

- Selection of the database (name), only specific customers!

- Selection of the customer (name), only specific test samples!

- Selection of the test sample (ID no.), depending on the customer / database!

- Selectthetestsampleinthe"IDno."lineandmarkitbymeansoftheinputstylus.

Now, the menu of the selected test sample opens. The values are highlighted in grey colour and

cannot be modiedin this menu!After pressing the <Start> button, rstthe "Visual Inspection"

menuisdisplayed.Conrmitbypressingabutton.Afterapositivetestandpressingabutton,a

connection test is started. The test is intended to determine whether a dangerous contact voltage

is applied, whether a test sample is connected and to make sure that there is no short-circuit. After

a positive connection test, the measurement is started. In case of a negative connection test (e.g.

open switch), an information message is displayed. The individual tests (depending on the pre-set-

tingofthetestprocedure)aredisplayedsubsequentlyandpartlyhavetobeactivatedorconrmed

by pressing the <Start> button (also see description of the individual measuring types, chapter 8). In

case of faulty individual results that are dangerous, the measurement will be interrupted immediate-

ly. By pressing the <Pause> button, it is possible to interrupt measurement so that e.g. the test cable

with the alligator clip or probe tip can be connected to another measuring point without resulting in

incorrect measurements / indications.

Attention!Themainsvoltageappliedtothetestsamplewillpersistduringthe"Testinterrupted"mes-

sage! Incorrect measured values can be deleted by pressing the <Reset> button. After the test has

beensuccessfulandisnished,the"TestsampleOK"menuisdisplayed.Itispossibletodisplaythe

results by pressing <Meas. Value> and to save them by pressing <Save>, <Yes>). The measuring

data will be stored in the selected database (name) and can be read out via a PC.

12.1 Searching Test Samples

By meansof the elds ( ) "DisplayAll"and "Next Test",you canselect the test samples ofa

specic"Database" and the corresponding "Customer"whichshallbetestedonaspecicdate.

Untick the box (  ) "Display All" and enter the corresponding date in the eld

"NextTest"bymeansofthecalendarfunction.Theresultisshownintheelds"No.ofTestSamples"and

"IDno.".Itispossibletolterandsearchfordifferentparameterslikee.g.theIDno.bymeansof

the"SearchField".

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning ST 750A Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Benning ST 750A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info