Bedienungsanleitung Benning ST 750A (Seite 44 von 58) (Englisch)

577368

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

08/ 2012 44 / 58



BENNING ST 750 A

17. RFID Reader (Optional)

RFIDisamethodforautomaticandelectronicidenticationofobjectsperradiotechnology. For

identicationoftheobject,thedatacanbereadoutbywirelesstechnologyviaaradiofrequency

channel. A marked object only sends its data, if the reader calls the transponder. An RFID system

consists of two components: a transponder and a reader. The transponder (in the following referred

toas"tag")istheactualdatacarrier.

It is possible to read it and to write on it without any contact by means of radio technology. The tag

stores data of the tag and of the connected object. The reader consists of a reader/writer unit with

antenna. The reader reads data of the tag and writes data to the tag. The reader is provided with a

USB 2.0 interface to transmit the received data to the BENNING ST 750 A Appliance Tester.

For installation of the tags, it has to be observed that metallic surfaces strongly interfere with the

radio connection. Therefore, do not install them directly onto metal or a metal housing. Data ex-

change between reader and transponder does not require direct contact (even not a visual contact).

Barcode labels can be exchanged by means of RFID transponders. The device communicates with

passive HF transponders with 13.56 MHz. The reading process is started by pressing a button. If

atransponderhasbeenidentied,thisisconrmedbyanacousticsignal.Itisnotnecessaryto

conguratetheRFIDreader.



WhenconnectingtheRFIDreader, rstswitchofftheBENNINGST750AAppliance

Tester! Do not remove / insert the RFID reader during operation. Always switch off the

devicerst!



In case of faults, switch off the appliance tester. Remove the RFID reader, reconnect it

and then switch on the appliance tester.

17.1 RFID Reader Specification

Benning part no.:

009370

Interface:

USB 2.0 interface

Operating voltage:

5V, supplied by USB interface of BENNING ST 750 A

Supported RFID transponders:

 13.56MHz,seechapter21"OptionalAccessories"

Reading range:

typ. 80 mm, depending on transponder

Typical reading time:

100 ms

Current consumption:

typ. 60 mA (passive mode)

typ. 120 mA (active mode)

Operating temperature:

0 °C to 50 °C

Storage temperature:

- 10 °C to 60 °C

Relative humidity:

20 % - 85 %

Protection category:

IP30

Dimensions:

approx. 165 x 110 x 80 mm

17.2 Operating the RFID Reader

The RFID reader can be used in combination with the following device groups: BENNING ST 750 A



For reading / writing processes, wait until the orange LED goes out.

An incorrect writing process will be signalled by two consecutive acoustic

signals. Repeat the process!

Commissioning:

- Switch the BENNING ST 750 A Appliance Tester OFF.

- Connect the RFID reader to the BENNING ST 750 A Appliance Tester (USB-A jack).

- Switch the BENNING ST 750 A Appliance Tester ON.

- MakesurethattheRFIDlamp("Power")switcheson.

Writing onto the transponder: (inventory data)

- Create the inventory data of a test sample in an internal database or select an existing test

sample (ID no.).

- <Select> <Save> and confirm the queries.

- Message: "Doyou want to save the data record on theRFID transponder?".Confirm with

<Yes>.

- The orange LED of the RFID reader flashes.

- Hold the scanning window of the RFID reader over the RFID transponder and press the button

on the bottom of the scanner.

- The writing process starts. Wait until the orange LED goes out and an acoustic signal is emitted.

- The data are saved on the RFID transponder.

An incorrect writing process will be signalled by two consecutive acoustic signals. Repeat

the process!

Writing onto the transponder: (measured values)

- Carry out the test.

- When the test result is displayed, select <Save>.

- Confirm the queries.

- Message: "Doyou want to save the data record on theRFID transponder?".Confirm with

<Yes>.

- The orange LED of the RFID reader flashes.

- Hold the scanning window of the RFID reader over the RFID transponder and press the button

on the bottom of the scanner.

- The writing process starts. Wait until the orange LED goes out and an acoustic signal is emitted.

- The data are saved on the RFID transponder.

An incorrect writing process will be signalled by two consecutive acoustic signals. Repeat

the process!

Reading the ID no. from the transponder and searching in internal database:

- Hold the scanning window of the RFID reader over the RFID transponder and press the button

on the bottom of the scanner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning ST 750A Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Benning ST 750A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info