Bedienungsanleitung Benno Pedelec - E-bike (Seite 42 von 72) (Englisch)

810831

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Rims made of composite materials

such as carbon bre in particular re-

quire special attention. Friction

caused by rim brakes, as well as just simply

riding the bike, puts a high amount of strain

on the bike.

• Only use brake pads that are designed for

use on the rims’ materials!

• Before every ride, check rims and wheels

made of composite materials for wear,

deformation, cracks and chipping!

• If you notice any changes, do not ride with

this part until it has been inspected by your

specialist retailer or manufacturer and

found to be in good condition!

• Never expose carbon bre parts to high

temperatures. Even intense sunlight (e.g.

when the wheel is stored in a vehicle) can

produce high temperatures. This may re-

sult in damage to the structure of the part.

Failure of parts, falls and very serious inju-

ries could result.

The permitted tire pressure may not

be exceeded when inating the

tires. Otherwise this could lead to a

tire bursting. The tires must be inated to at

least the stated minimum tire pressure. If the

tire pressure is too low, there is a possibility

that the tire could free itself from the rim.

On the side surface of the tire, there is in-

formation on the maximum permitted tire

pressure and generally also on the mini-

mum permitted tire pressure. If you replace

the tires, only exchange them for the same

model with the same dimensions and pro-

le. The riding experience can otherwise be

negatively affected.

If the ination pressure rating indicated on

the tire and on the rim differ, the lowest max-

imum pressure and the highest minimum

pressure apply.

Tires are available in various di-

mensions. The tire dimensions are

provided with standardised informa-

tion.

Example 1: “46-622” means that the tires

have a width of 46 mm and the rim has a

diameter of 622 mm.

Example 2: “28 x 1.60” states that the tire

has a diameter of 28 inches and a width of

1.60 inches.

Tires and tire pressure

The amounts for the recommended tire pressure

can either be named in bar or PSI. The follow-

ing table presents the conversions for the usu-

al pressure levels and shows which tire widths

these pressures should be applied to.

Tire width Recommended tire

pressure

20 mm 9.0 bar 130 psi

23 mm 8.0 bar 115 psi

25 mm 7.0 bar 100 psi

28 mm 6.0 bar 85 psi

30 mm 5.5 bar 80 psi

32 mm 5.0 bar 70 psi

35 mm 4.5 bar 65 psi

37 mm 4.5 bar 65 psi

40 mm 4.0 bar 55 psi

42 mm 4.0 bar 55 psi

44 mm 3.5 bar 50 psi

47 mm 3.5 bar 50 psi

50 mm 3.0 bar 45 psi

54 mm 2.5 bar 35 psi

57 mm 2.2 bar 32 psi

60 mm 2.0 bar 30 psi

You must observe the information

provided by tire and rim manufac-

turers. This could possibly be differ-

ent from the tire pressures listed here. Not

adhering to these guidelines can lead to

damage to your tires and inner tubes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benno Pedelec - E-bike Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Benno Pedelec - E-bike

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info