784247
11
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
11
Installation
6006113_a – 01.06.2022
EN
Seal the cut surface of the work top with suitable material
(heat resistant to 75 °C – e.g. special paint, silicone rubber
or cast resin).
For the material used, the worktop manufacturers
instructions must be followed.
Place the hob into the specified position in the lower
cabinet from above.
3.3.5 Establish electrical power supply
DWARNING!
Risk of death due to electric shock!
Touching live parts can cause an electric shock, burns or
death.
Ensure that the voltage supply is and remains
disconnected while the following work is in progress.
DATTENTION!
Danger of property damage due to incorrect connection!
If the hob is connected with further devices (e.g. oven),
damage can arise due to overvoltage. The customer must
provide a separate connection point with dedicated fuse for
the hob.
Make sure that the device is connected separately.
Make sure the connection is separately protected with a
circuit breaker and a residual current device.
Observe the voltage specifications on the ratings plate.
Connect the device to the power supply provided by the
customer. The junction box is located on the underside of
the device.
Connection to spring-loaded terminals (e.g. in cooker
connection boxes) is not permitted.
Connection possibilities:
y400 V ~ / 50/60 Hz – 2P+N
NL1L2
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 4 x 2.5 mm2,
Fuse 16 A
y230 V ~ / 50/60 Hz – 1P+N
(optional, not compatible with AutoRun module)
NL1
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 3 x 4.0 mm2,
Fuse 40 A
Route the cables so that they are not kinked, crushed or
damaged and do not come into contact with hot parts of
the device.
Make sure that the device can be disconnected on all
poles from the electricity supply after installation.
After switching on the power supply, the device is ready for
operation.
3.3.6 Check and carry out commissioning
DATTENTION!
Risk of disruptions due to moisture in the device!
If the device is moved from a cold environment into a hot
one, condensation may form inside.
Wait about 2-3 hours before bringing the device into
service.
Ensure that the device is accessible for maintenance work
at all times.
Check that an all-pole isolating device (min. 3 mm contact
gap) is present.
Check that the mains cable and the electrical connection
cable are not kinked, crushed or damaged.
Make sure that the protective film is removed.
Check the correct functioning of the device.
D“4. Operation (page 12).
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Berbel BKF 90 iPP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Berbel BKF 90 iPP

Berbel BKF 90 iPP Bedienungsanleitung - Deutsch - 36 seiten

Berbel BKF 90 iPP Bedienungsanleitung - Holländisch - 36 seiten

Berbel BKF 90 iPP Bedienungsanleitung - Französisch - 36 seiten

Berbel BKF 90 iPP Bedienungsanleitung - Italienisch - 36 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info