Bedienungsanleitung Bergamont Pedelec 2016 (Seite 29 von 87) (Englisch)

779501

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

56 57

MTB-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2016 ORIGINAL OPERATING INSTRUCTIONS 2016 | MTB-PEDELEC

b ca e fd

ENGLISH

DANGER!

Poorly tightened or loosening bolts can fail. Risk of accident!

DANGER!

Check the bolts by using a torque wrench once a month according to the

values indicated directly on the components and/or in the manuals of the

component manufacturers on this BERGAMONT info CD.

Clamping with two bolts in line (d): Release both bolts two to three turns

anticlockwise, otherwise the whole assembly can come apart. Move the saddle

forward or backward as desired to adjust the horizontal position. You may have

to give the saddle a light blow to make it move. Please observe the markings on

the saddle rail.

Having found your preferred position, make sure both clamp halves fit snugly

around the saddle rails before tightening the bolt(s) to the correct torque value

as prescribed by the seat post manufacturer.

Tighten both bolts evenly (e) so the saddle remains at the same angle. If you

wish to lower the nose of the saddle a little, tighten the front bolt clockwise. You

might have to loosen the rear bolt a little as well. To lower the rear part of the

saddle, the rear bolt has to be tightened clockwise (e) and the front bolt has to

be released, if necessary. After fastening the saddle, check whether it resists

tilting by bringing your weight to bear on it once with your hands at either end

of the saddle (f).

DANGER!

Check the bolts by using a torque wrench once a month according to the

values indicated directly on the components and/or in the manuals of the

component manufacturers on this BERGAMONT info CD.

DANGER!

Poorly tightened or loosening bolts can fail. Risk of accident!

NOTE!

The manufacturers of saddles deliver their products with detailed manuals.

You find these manuals on this BERGAMONT info CD. Read them carefully

before adjusting the position of your saddle. If you are in doubt or if you have

any questions, contact your BERGAMONT dealer.

Adjustment of saddle position and tilt

With patent seat posts (a) one or two bolts fix the clamping mechanism, which

controls the tilt and the horizontal position of the saddle. Some seat posts have

two bolts side-by-side.

Release the bolt(s) at the top of the seat post. Release the bolt(s) two to three

turns anticlockwise at the most, otherwise the whole assembly can come apart.

Move the saddle forth or back, as desired. You may have to give the saddle a

light blow to make it move.

Please observe the markings on the saddle rail. Make sure the seat of the saddle

remains horizontal (b) as you retighten the bolt(s). Your BERGAMONT bike

should stand on level ground while you adjust the saddle.

Having found your preferred position, make sure both clamp halves fit snugly

around the saddle rails before tightening the bolt(s) to the correct torque value

as prescribed by the seat post manufacturer.

Retighten the bolt(s) with a torque wrench according to the manuals of the

manufacturer. After fastening the saddle, check whether it resists tilting by

bringing your weight to bear on it once with your hands at either end of the

saddle (c).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bergamont Pedelec 2016 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info