Bedienungsanleitung Bergamont Pedelec 2016 (Seite 30 von 87) (Englisch)

779501

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

58 59

MTB-PEDELEC | ORIGINAL OPERATING INSTRUCTIONS 2016 ORIGINAL OPERATING INSTRUCTIONS 2016 | MTB-PEDELEC

b ca e fd

ENGLISH

If the saddle rails fit into the clamp grooves, slide the saddle on the seat post

and ensure that the clamp is positioned midway along the total length of the

rails. Position the saddle so that its upper surface is parallel to the ground. Tight-

en the bolt gradually and make sure

1) the clamping device is still accurately mounted on the carbon seat post head

and that

2) the clamp is tightening evenly around each rail.

Once there is uniform hold on both rails, tighten the bolt gradually with a torque

wrench (d) until you have reached the maximum torque value indicated in New-

ton meters (Nm) on the seat post.

DANGER!

Check the bolts by using a torque wrench once a month according to the

values indicated directly on the components and/or in the manuals of the

component manufacturers on this BERGAMONT info CD.

DANGER!

Poorly tightened or loosening bolts can fail. Risk of accident!

COCKPIT ADJUSTMENT

Brake lever reach adjustment on BERGAMONT mountain bikes

With most brake systems the distance between the brake levers and the han-

dlebar grips is adjustable. This gives in particular riders with small hands the

convenience of bringing the brake levers closer to the handlebars (e).

On most bikes there is a small adjusting screw near the point where the brake

cable of a cable brake enters the brake lever unit or at the lever itself. Turn this

bolt clockwise and watch how the lever adjusts as you do so (f). Note that the

brake lever has a free travel of one third before the pressure point of the brake is

reached.

If you have a single bolt system (a), the seat post for most of the sports saddles

is designed for a saddle rail diameter of 7 mm. Replacement outer clamps for

ovalized saddle rails of 8 mm x 8.5 mm (W x H) as well as for carbon saddle rails

bigger than 8 x 8.5 mm are also available. If you are not sure which saddle rail

type you have or if you need further information, contact your BERGAMONT

dealer.

To mount the saddle unscrew the transversal fixing bolt as far as possible with-

out loosening the lock nut on the outer side of the clamping device (b). In gen-

eral, it is not necessary to take the mechanism completely apart, if it is already

equipped with the correct outer clamps for your saddle.

If you do find it necessary to unscrew the single fixing bolt completely, remove

it from the clamping device. This releases the outer clamping parts. The inner

clamping parts are typically held in position with a rubber retention plate.

Mount the saddle rails into the inner clamping parts, add the outer parts and

re-insert the fixing bolt. If the width of the saddle rails does not fit exactly into

the clamp grooves, do not try to force them in. The clamping mechanism or the

saddle rails could break and result in an accident and/or injuries to the rider.

Use a different saddle model (c) or contact your BERGAMONT dealer.

DANGER!

When choosing another saddle, observe that there are round and ovalized

rails. Replace the fitting pieces of the clamp accordingly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bergamont Pedelec 2016 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info