Bedienungsanleitung Berner GA401 (Seite 43 von 67) (Deutsch, Englisch, Holländisch, Französisch)

474163

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

ENGLISH

Special functions and any other adjustment

possibilities of the garage door operator

5.1 Second opening position (airing position)

In the airing position a second opening position can be

freely programmed. The latter is switched by channel 2 of

the radio receiver. Terminal 20 (0 V) and 23 (impulse input

partial opening). Set DIP switch 7 (SCH2) to OFF.

5.1.1 Programming the second opening position (airing

position)

The operator is ready for use and the operator stands still.

Check again if the the guiding hitch is clutched in the

flange lock / belt lock (see figure 17).

1) Press the black button (for approx. 6 sec.) until the

lamp starts flashing. Allow to flash twice, then press

additionally the white button and press (for approx. 2

sec.) until the lamp quickly flashes twice. Then

release both buttons.

2) Now press the white operating button so that the

door can travel to its "Second opening" position. The

door moves as long as the white button stays pressed

(permanent contact). Once the button is released,

the door stops immediately. The next time the button

is pressed, the door travels in the opposite direction.

This procedure is repeated until the desired "Second

opening" position is reached.

3) Briefly press the black “learn” button. The operator

lighting is switched on. “Second opening position” is

now programmed.

5.2 Defined direction instructions

A defined direction option is adjustable through DIP switch

7 (SCH2).

1) radio channel 1 (terminal 20/21) = open – stop – open

etc.

2) radio channel 2 (terminal 20/23) = closed – stop –

closed etc.

3) Set DIP switch 7 (SCH2) to ON

5.3 Quick-opening function

The quick-opening function is selectable through DIP

switch 3 (SCH2). Thereby: up to 50 % higher opening

speed*.

1) Set DIP 3 (SCH2) to ON = quick-opening speed

2) Set DIP 3 (SCH2) to OFF = normal opening speed

* depending on the door

Note

The motor of the garage door operator is equipped with a

thermal overload protection. In case of 2-3 quick door runs in

“OPEN” position (max 40 sec.) within 2 minutes, this overload

protection reduces the door speed, i.e. the door travels in

direction “OPEN” and “CLOSED” have the usual speed. After a

rest period of 2 additional minutes, the next run in direction

“OPEN” is executed quickly.

ATTENTION: danger to life

This function is not to be selected for

tipping and swing doors, but only for

holohedrally closed sectional doors!

* Accessory, is not included in delivery!

Note

After changing the door speed the operator has to be newly

programmed!

5.4 Soft-stop

Soft-start is adjustable with DIP switch 4 (SCH2) before

reaching end-of-travel position “CLOSED”

1) Set DIP 4 (SCH2) to ON = 30 % soft-stop – up and

over door

2) Set DIP 4 (SCH2) to OFF = 50 % soft-travel speed

5.5 Short return to the position “door closed”

The short return to the position “door closed” is

adjustable with DIP switch 5 (SCH2), i.e. the slide moves

briefly to position “OPEN” when reaching “CLOSED” .

1) Set DIP 5 (SCH2) to ON = short return “long”

2) Set DIP 5 (SCH2) to OFF = short return “very short”

Note

If DIP5 is activated during the memorising process, the

following functions are activated:

1) DIP5 (SCH2) set to ON = Short return “very short”

2) DIP5 (SCH2) set to OFF = Short reverse deactivated

On each new memorising process this procedure has to be

repeated.

5.6 Automatic timer

With this function, the door is automatically closed after

a preset open phase has elapsed. According to EN 12453

Tab.1, this function is only permitted if combined with a

photocell.

Note

If the "automatic timer" is set, impulse operation is not

possible. Each command causes the door to open or

the open phase to be reset.

A closing from the position “partial opening” occurs only if the

distance to the end-of-travel position “door CLOSED” is

> 500 mm. In case of a smaller distance, the door has to be

closed by reoperating the button “partial opening”.

5.6.1 Programming the automatic timer / early warning

phase

The door must be at a standstill and ready for operation.

Briefly press the black "learn" button (lamp flashes five

times), wait till the desired open phase is over (min.

10 sec. to max. 150 sec.). Then briefly press the black

"learn" button, the lamp continues to flash five times. You

must now wait for the early warning phase to be set (min.

3 sec. to max. 30 sec.), then briefly press the black "learn"

button again. You have now activated the automatic timer.

In this mode the door can only be opened via radio and

button. If a command is given during the closing phase,

the door reverses and travels to its "OPEN" position.

Automatic closing only takes place from the "OPEN"

position provided no safety circuit has been broken and

the open phase has elapsed.

Note

If, on account of the overcurrent cutoff, the door has

reversed twice to its "OPEN" end-of-travel position, the

automatic timer will be blocked. The garage lighting signals

the impulse code for "twice safety device" and an

acknowledgement

via the button must be issued. The open phase

will not start running until this acknowledgement has been

issued.

Berner GA401 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info