Bedienungsanleitung Berner GA401 (Seite 44 von 67) (Deutsch, Englisch, Holländisch, Französisch)

474163

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

ENGLISH

5.6.2 Automatic timer “OFF”

Briefly press black “learn” button consecutively twice.

5.7 Light at “CLOSE”

If the lighting is to stay on even with the door closed,

(operator lighting stays switched on for approx.150 sec.

when door is closed) this can be achieved by the following

action:

1) First unplug from the mains.

2) Press the black "learn" button and keep it pressed.

3) Plug back into the mains.

4) After the lamp has switched on, release the "learn"

button.

On repeating the procedure, at the "CLOSE" position

the light switches off again to 5 sec. lightning time.

6 Use of the garage door operator

Only ever operate the garage door operator provided

you have a full view of the door's area of movement.

Wait until the door has come to a complete halt before

entering the door's area of movement.

Before driving in or out of the garage, always check that

the door has fully opened!

Note

Initial function checks as well as programming or extending the

remote control should always take place from inside the garage.

ATTENTION

Keep hand transmitters out of the

reach of children!

The function of the mechanical release should be

checked every month. The pull cord with knob may

only be actuated when the door is closed, otherwise

with weak, broken or defective springs or due to

inadequate counterbalancing, there is a risk that the door

could close too quickly.

ATTENTION

Never hang bodily from the pull cord

with knob!

All persons using the door system must

be shown how to operate the garage

door operator properly and safely.

Demonstrate

and test the mechanical release as

well as the safety return. To do this,

halt the movement of the closing

door by grasping it with both hands.

The door system should gently cut-

out and initiate the safety return. The

same should happen during the

opening cycle, i.e. the door system gently cuts out and the

door comes to a halt.

6.1 Normal operation

In the normal operation mode the garage door operator

works entirely according to impulse repetition control,

whereby it makes no difference whether an external

button, a programmed-in hand transmitter button or

the test button on the control PCB is pressed:

1st impulse: The door travels towards an end-of-travel

position.

2nd impulse: the door stops.

3rd impulse: the door travels in the opposite direction.

4th impulse: the door stops.

5th impulse: the door travels in the direction of the end-

of-travel position selected with the 1st

impulse etc.

The operator lighting comes on when the door starts to

move and automatically goes out 5 or 150 sec. later on

completion of the cycle.

6.2 Operation following actuation of the mechanical/

manual release

If, for instance due to a mains power failure, the

mechanical release was actuated, the carriage must

reengage in the door link latch before normal operation

can be resumed:

1) Press the green button on the carriage (see figure 17).

2) Move the door manually until the carriage reengages

in the door link latch.

3) Allow the door to complete several uninterrupted

opening and closing cycles to check whether it has

fully closed and fully opened.

The operator is now ready again to resume normal

operation.

Note

If, after carrying out several interrupted door cycles,

the behaviour of the door does not correspond to that

described in stage 3, it will be necessary to rerun the

learning procedure (see section 3.2.2).

6.3 Error messages operator lighting / LED-diagnosis

(Lighting diodes, see figure 7.1)

Via the LED-diagnosis 3 and 4, which are visible after

opening the transparent lid, causes for malfunctions can

be easily identified. During the normal operation these

LEDs are not lighting.

Lighting: flashes once within 1 second

LED: 4 glows

Cause: A emergency-stop function connected to

terminals 12 and 13 has been interrupted or

activated (see section 4.8).

Remedy: The STOP or emergency-OFF circuit is to be

closed.

Note: If a STOP or emergency-OFF circuit is not

connected to terminals 12 and 13, check

whether the DIP switch 1 (SCH1) is set at

"ON".

Lighting: flashes once within 1 second

LED: 4 flashes

Cause: A photocell connected to terminals 20 and 71

has been interrupted or activated (see

section 4.9/4.10).

Remedy: Remove the obstruction causing the problem

and/or check the photocell, if necessary

replace.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berner GA401 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info