Bedienungsanleitung Bestron AAC9000 (Seite 46 von 75) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

702402

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

USAGE - Timer function

The device has a time switch with which you can automatically turn the device on or off at the end of a set

time.

Automatically turning on

When the device is turned off:

1. Press the button “timer” (figure 1, C). The display starts to flicker.

2. Use the “timer” button to set the switch-on time between 1 and 24 hours.

3. Wait until the display (A) stops flickering. The switch-on time is set.

4. Press the button “timer” again to adjust the switch-on time if desired.

Automatically turning off

When the device is turned on:

1. Press the button “timer” (figure 1, b). The display starts to flicker.

2. Use the “timer” button to set the switch-on time between 1 and 24 hours.

3. Wait until the display (A) stops flickering. The switch-off time is set.

4. Press the button “timer” again to adjust the switch-off time if desired.

USAGE - Remote control

The device can also be controlled with the included remote control. The remote control requires two AAA-

batteries (not included). Open the battery compartment on the underside, place the batteries and close the

lid. The buttons on the remote control function the same as the buttons on the control panel.

For an optimal functioning:

• Make sure the distance between the ventilator and the remote control isn’t greater than 6 metres.

• Aim the remote control at the device and make sure the direction angle is smaller than 30 degrees.

CLEANING AND MAINTENANCE - General

After a period of time, dust can get into the rosters and the slats of the device.

1. Turn off the device and pull the plug from the socket.

2. Remove the dust of the rosters and slats with a hand brush and/or vacuum cleaner.

3. Clean the casing with a soft, moist cloth. Never immerse the device in water. Make sure no moist can

get into the electrical connections.

CLEANING AND MAINTENANCE - Water drainage

The device has an internal water collection tray. When it is full, the device stops functioning and the indication

light lights up on the control panel at “water full”.

1. Turn off the device and pull the plug from the

socket.

2. Place the device on an elevation, and place a

bucket or other kind of collection tray underneath

the drain hole of the water collection tray.

3. Unscrew the lid and plug of the drain hole (figure

1, No. 12), see figure 6. The water streams from

the water collection tray in the bucket.

4. If the water collection tray is empty, put the lid

and plug back in the drain hole, and make sure

it is properly closed.

ATTENTION:

• Carefully move the device and keep it upright at all times, to prevent spillage of the water over the brim

of the internal water collection tray. During emptying, you can slant the device slightly to remove the last

water from the water collection tray.

• If the bucket, or other kind of collection tray, cannot collect all the water at the same time, put the lid and

plug of drain hole back. Empty the bucket and repeat the steps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestron AAC9000 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info