Bedienungsanleitung Bestway 58259 (Seite 4 von 6) (Englisch)

752356

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

RESET

P6124

Hose

Clamp P6176

Hose

P6005 O-Ring

NOTE: To order spare parts for

the Pool Heater, please provide

us with part no. and part name.

Drawings for illustration

purposes only. May not reflect

actual product. Not to scale.

Assembly

1. Set-up and fill the pool with water to the required level according to the

pool’s owner’s manual.

2. Attach the Filter Pump or Sand Filter’s Inlet Valve to the Pool:

a) Place the loose Hose Clamps on both ends of a Filter Pump or Sand

Filter Hose.

b) Attach the hose to Filter Pump or Sand Filter’s Inlet Valve and the Pool’s

Outlet Valve.

c) Tighten the Hose Clamps.

3. Connect the Filter Pump or Sand Filter to the Pool Heater:

a) Place the loose Hose Clamps on both ends of the Pool Heater Hose.

b) Attach the hose to the Filter Pump or Sand Filter’s Outlet Valve and the

Pool Heater’s ‘INLET’ Valve and tighten the Hose Clamps.

4. Attach the Pool Heater to the Pool.

5. Loosen the Hose Clamps on the Pool’s Inlet and Outlet Valves; replace the

Stopper Plugs with Debris Screens. Water now flows to the Filter Pump or

Sand Filter and the Pool Heater. With the Hoses and the Debris Screens in

position, tighten the Hose Clamps.

6. Check that every port and valve is connected correctly.

Filter Pump

Above Ground Pool

Water Level

Sand Filter

P6124

Pedestal Fixing

The pool heater must be vertically fixed on ground or a certain pedestal made of wood or concrete before it can be used. There

should be two holes, 8mm in diameter on the pedestal, the space between which should be 254mm. Put the pool heater on the

pedestal and fix them together with bolts and nuts. The pedestal should weigh over 18kgs in order to prevent the pool heater from

accidentally falling.

Operation

1. Check the pool for correct installation and make sure both the pool’s Inlet

and Outlet Valves are fully covered by water before operating the Filter

Pump or Sand Filter of the Pool Heater. Make sure that the Pool Heater

and Filter Pump or Sand Filter are correctly connected.

2. Start the Filter Pump or Sand Filter according to the owner’s manual.

3. With the pump operating, insert the plug of Pool Heater into a socket.

4. Press the “-/O” button of the Pool Heater, the LED light turns on.

5. Press the “TEST” button, the LED light turns off.

6. Press the “-/O” button, and the Pool Heater is ready to use.

NOTE: The Pool Heater must be tested before each use.

NOTE: Never plug in the Pool Heater until the Filter Pump or Sand Filter has

been plugged in.

NOTE: To prevent the risk of electrical shock, ensure your hands are

completely dry when plugging-in the Filter Pump or Sand Filter and the

Pool Heater.

NOTE: To prevent the risk of electrical shock, never run the Filter Pump or

Sand Filter and the Pool Heater when people are in the pool.

NOTE: Do not dry run the Pool Heater. Damage caused by dry running the

Pool Heater is not covered by the manufacturer’s warranty.

7. Remember to disconnect the Pool Heater first. Never unplug the Filter

Pump or Sand Filter when the Pool Heater is running.

8. Unplug the Filter Pump or Sand Filter and enjoy warm pool water!

Maintenance

CAUTION: YOU MUST UNPLUG THE POOL HEATER FIRST,

THEN UNPLUG THE FILTER PUMP OR SAND FILTER BEFORE

PREFORMING MAINTENANCE OR SEVERE RISK OF INJURY OR

DEATH EXISTS.

1. Stop Water Flowing to the Filter Pump or Sand Filter and the Pool Heater:

a) Disconnect the Pool Heater and THEN the Filter Pump or Sand Filter .

b) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses.

c) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet

and Outlet Valves.

d) Refer to the Filter Pump or Sand Filter ’s Owner’s Manual for information

on Filter Pump or Sand Filter maintenance.

2. After Filter Pump or Sand Filter maintenance, replace the Stopper Plugs

with the Debris Screens in the pool’s Inlet and Outlet Valves. Water will now

flow to the Filter Pump or Sand Filter and the Pool Heater.

3. Operate as outlined in the Operation section of this manual.

Storage and Winterization

CAUTION: YOU MUST UNPLUG THE POOL HEATER AND THE

FILTER PUMP OR SAND FILTER BEFORE MAINTENANCE

BEGINS OR SEVERE RISK OF INJURY OR DEATH EXISTS.

To avoid damage, pool equipment must be winterized when temperatures

decrease. Allowing water to freeze will damage the Pool Heater and void the

warranty.

The heater shall not be left out in the open air for long periods of time. When it

is not in used, please store it in a cool, dry place once it has been cleaned

and dried.

1. Follow the instructions previously outline to stop water flowing to the Filter

Pump or Sand Filter and the Pool Heater.

2. Detach all hoses.

3. Drain any water in the Pool Heater and clean all components thoroughly.

4. Put the Pool Heater in a cool, dry place, out of children’s reach.

Heating Reset

1. Be sure to press the "Reset" button on the

pool heater using a small and thin object before

initial operation

2. If the pool heater is not heating properly, press the "Reset"

button on the pool heater.

254 MM

8 MM

S-S-001462

S-S-001462/14.0x21.0cm (#58259GB 英规加热器说明书D版) JS-YF-2012-B-01266/英

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bestway 58259 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bestway 58259

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info