Bedienungsanleitung Bestway 65077 Hydro-Force (Seite 3 von 32) (Alle Sprachen)

753216

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

WARNING

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you don’t follow these instructions, it may cause

the boat to overturn or explode and result in drowning.

1. Do not exceed the maximum recommended number of persons. Regardless of the number of

persons on board, the total weight of persons and equipment must never exceed the maximum

recommended load. Always use the seats /seating spaces provided.

2. When loading the craft, never exceed the maximum recommended load: Always load the craft

carefully and distribute loads appropriately to maintain design trim (approximately level). Avoid

placing heavy weights high up.

NOTE: The maximum recommended load includes the weight of all persons onboard, all

provisions and personal effects, any equipment not included in the light craft mass, cargo (if any)

and all consumable liquids (water, fuel, etc.).

3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected

and used at all times.

4. Before every use, carefully inspect all boat components including air-chambers, grab ropes,

oars, and air valves, to ensure everything is in good condition and tightly secured. If you find any

damage, please stop to repair it.

5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the

boat takes on water.

6. When the boat is in motion, all passengers must remain seated at all times to avoid falling

overboard. Keep the boat balanced. Uneven distribution of persons or load in the boat may

cause the boat to overturn and result in drowning.

7. Use the craft in sheltered water, up to 300m (984 feet). Be careful with natural factors such as

wind, tide waters and tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.

Always wear a lifejacket!

8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the

other air chamber to prevent the boat from sinking.

9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells,

glass, etc. may puncture the boat. To avoid damage, do not drag the boat on rough surfaces.

10. The boat is intended for beach use, short-time and short-distance cruising.

11. Be aware of the potential harmful effects of liquids such as battery acid, oil or petrol. The liquids

may damage your boat.

12. Inflate according to the numbered air chamber and rated pressure of the boat, or it will cause

over-inflation and potential and boat explosion. Exceeding the data given on the capacity plate

may cause the craft to be damaged, overturn and lead to drowning.

13. Know how to operate a boat. Check in your local area for information and/or training as needed.

Inform yourself about local regulations and dangers related to boating and/or other water

activities.

SAVE THESE INSTRUCTIONS

Assembling of the boat

NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR

PRODUCT AND VOID YOUR WARRANTY

1. Spread out the boat on level ground.

2. Assemble the removable fin to the bottom of the boat (Fig.1). Make sure the curvature of the fin is

pointed towards the back end of the boat.

NOTE: Assemble the fin before inflation and also disassemble it after deflation.

NOTE: To avoid damage to the removable fin, do not enter shallow water.

WARNING: To avoid damage to the boat and injury to passengers, please don’t

exceed the data given on the builder’s plate.

Technical Specifications

0.04 bar

0.6 psi

Item

65077

Maximum Number of Persons

2 adults

Maximum Load Capacity

160 kg (350 Ibs.)

Inflated Size Recommended

Working Pressure

Item

65077 3.21m x 88cm (10'6" x 35") 10cm 11.1cm

Product Inflated Size Deflated Size Inflated Size

• Inflate the air chambers with a HAND air pump.

An inflation scale is provided with the product.

Inflate the product until the printed scale is charged up to the same level as that of the supplied

scale. (refer the belowing Table and Illustration)

Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the

pressure of the boat each time before using. If you use other pressure gauge, the boat pressure

should not be more than the data given on the builder’s plate.

• Never stand on or rest objects on the boat during inflation.

• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.

• Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in

direct sunlight for more than 1 hour after use.

5. Fold the boat from front to back to remove additional air. You can also use a pump to drain any

remaining air.

Repair

1. If there is a small puncture, repair it according to the instruction on repair

patch.

2. If the hole is too big to be repaired with the provided patch, purchase a

Bestway repair kit or send the boat to a speciality shop to make the repair.

Registration (For US/Canada customers only)

If you need to register your boat, please have the boat Hull Identification Number and model name

ready and then visit www.bestwaycorp.com/support to obtain your Certificate of Origin, or you can

send e-mail to service@bestwaycorp.us for the Certificate of Origin.

PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW

OWNER WHEN YOU SELL THE CRAFT.

NOTE: All drawings for illustration purpose only. May not reflect actual product.

Storage

1. Keep all accessories for future use.

2. Carefully clean the boat using a mild soap with clean water.

Note: Do not use acetone, acid, and/or alkaline solutions.

3. Use a cloth to gently dry all surfaces.

Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric

blowers. Doing so will cause damage and shorten the boat’s life span.

4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure

drops together. This will prevent damage from occurring to the boat inner structures. Next deflate

the floor and seat.

Oars Installation

Seat and footrest assembly

Assemble the belt to the seat and tie to the boat.

Put the inflated footrest into the front of the boat, make sure the footrest not entangle the feet of the

occupants in the event of a capsize.

3.21m x 88cm

(10'6" x 35")

Fig. 1

mc1112

1112

131415

OWNER’S MANUAL

LITE-RAPID X2 KAYAK

Oar

Boat

Components:

• Repair Patch

• Deflation Pipe

Oar blade x 4

Shaft x 2

Coupling x 4

Rope x 2

Fabric Tape x 2

• Inflation Scale

Footrest Cushion

Oar ring x 4

Removable Fin

Hand Pump

65077

Bestway 65077 Hydro-Force Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info