Bedienungsanleitung Beurer BG28 (Seite 10 von 44) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

470240

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

3. Operation

3.1 Batteries

If present, pull the battery insulating strip off the battery compartment cover or re-

move the battery’s protective film and insert the battery according to the polarity.

If the scale fails to operate, remove the battery completely and insert it again. Your

scale is equipped with a “replace battery” indicator. When the scale is operated with

a battery which is too weak, “Lo” appears in the display field and the scale auto-

matically switches off. The battery must be replaced in this case (3 V lithium battery

CR2032). The used, completely drained standard and rechargeable batteries must

be disposed of in specially marked collection containers, at toxic waste collection

points or electrical product retailers. You are legally obligated to dispose of the bat-

teries.

Note: Batteries containing pollutants are marked with the following symbols:

Pb = Battery contains lead, Cd = Battery contains cadmium, Hg = Battery contains

mercury.

Place the scale on a firm, flat surface; a firm floor covering is a basic requirement for

correct weight measurement.

3.2 Measuring weight only

Place the scale on a firm level floor (no carpet); a firm floor covering

is required for correct measurement.

Audibly, briefly and firmly tap the scale with your foot to active the

vibration sensor!

The entire display (Fig. 1) appears up to “0.0” (Fig. 2) as a self-test (tap-

on technology).

Now the scale is ready to measure your weight. Stand on the scale wi-

thout moving about and distribute your weight evenly on both legs. The

scale immediately begins to measure your weight. Your measured weight

is displayed shortly after this (Fig 3). The scale switches off a few se-

conds after you step down from it.

3.3 Measuring weight, body fat, body water and muscle

percentage

– First your personal parameters must be stored;

– Briefly step onto the scale first and wait until the display “0.0” (Fig. 2)

appears. Then press “SET”. Now the first memory preset flashes in the

display (Fig. 4). Select the desired preset by pressing the buttons “up”

or “down” and confirm the desired preset with the “SET” button.

– Now height in cm (inch) flashes in the display (Fig. 5). Set the desired

value by briefly pressing or holding the buttons “up”

or “down”

and confirm it by pressing “SET”.

– “Age” in years then flashes in the display (Fig. 6). Set the desired value

by briefly pressing or holding the buttons “up”

or “down” and

confirm it by pressing “SET”.

– The sex setting “Woman” or “Man” appears on the display (Fig. 7). Se-

lect your sex by pressing the buttons “up”

or “down” and confirm

by pressing “SET”.

– Now the setting for your individual level of activity or fitness appears

on the display (Fig. 8). Select the desired level of activity by pressing

the buttons “up”

or “down” and confirm the desired level of acti-

vity with the “SET” button.

– The values you’ve just set are displayed again consecutively.

Pb Cd Hg

Fig. 5

Fig. 6

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer BG28 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beurer BG28

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info