Bedienungsanleitung Beurer IPL 10000 plus (Seite 33 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568802

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Using skin tone detection

1. To begin skin tone detection, simultaneously press down both energy level selection buttons

(+ and -) for 2 seconds.

2. Skin tone detection is active when the individual energy indicator LEDs light up in sequence from

left to right.

3. Now place the light area of the cartridge on the desired test area and make sure it is in full contact

with the skin.

Note

For your safety, always select the darkest area of skin (e.g. the outer side of the lower leg, back of

the hand on the arm)

Important: Before using on another part of the body, you must take another measurement.

4. Press the trigger button to begin skin tone detection. Skin tone detection can take 1 – 2 seconds.

Note

The device does not trigger any light pulses in skin tone detection mode.

5. If the skin tone measurement is successful, the suitable energy level for your skin tone appears on

the energy indicator lamp. The LEDs of the displayed energy level remain permanently lit.

6. If the energy indicator lamp lights up from left to right as before, skin tone detection was unsuc-

cessful.

7. Check the indicator lamp on the applicator. If the indicator lamp is orange, there was not enough

contact with the skin to take a measurement. If the indicator lamp is red, your skin is either too dark

or the skin tone cannot be detected.

8. If this is the case, press the trigger button again to repeat the measurement.

Note

If you want to cancel skin tone detection, press one of the energy level selection buttons (+ or -)

again to return to normal mode.

9. If skin tone detection was successful, check the result of the measurement by comparing it with the

skin and hair colour table.

10. If the value measured differs from the skin and hair colour table, you should always use the lower

energy level.

11. You can increase and decrease the energy level at any time by pressing the + and - buttons.

If you notice slight or no irritation during and after the first hair removal treatment while using the rec-

ommended energy level, you may increase the energy level by 1 in subsequent treatments.

WARNING

Do not increase the energy level if you experience an abnormal amount of pain during or after the

treatment using the beurer SalonPro System! (See “Step 6 Familiarise yourself with the possible side-

effects”)

Do not increase the energy level during the hair removal session, even if you do not notice any dis-

comfort.

Irritation can occur some time after the treatment itself.

STEP 6: Familiarise yourself with the possible side-effects of using the beurer SalonPro System

If the beurer SalonPro System is used in accordance with these instructions for use, side effects and

complications seldom occur in relation to the use of the beurer SalonPro System. However, every cos-

metic treatment method – including methods such as these designed for use at home – is associated

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer IPL 10000 plus Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info