Bedienungsanleitung Bianco di puro Gusto Alpha (Seite 7 von 12) (Englisch)

814572

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

12 13

Control Panel

Start/Stop button

Connect power cord and container to the device. Press this button to be sure that the device is in Standby mode. If

you select a program and press this button, the operation of that program will start. Pressing this button will stop the

operation immediately when the device runs in Program mode or Manual mode.

Program button

This device contains five default programs. When pressing the button, the program sounds a short beep and starts

flashing. For more information about default program, please refer to the page 15. This button also can be used as

Selfsetting program. Please refer to page 13 for more detailed information about Self-setting program.

Time setting button

The operation time can be selected from Manual mode. Press the button increases or decreases the time in one second

for short press and ten seconds for long press. For more information about Manual mode, please refer to the page 14.

Speed control knob

The speed is adjustable by controlling Speed control knob in Manual mode. Turning the Speed control knob to the right

slowly increases the speed. Turning the Speed control knob to the left slowly decreases the speed. For more information

about Manual mode, please refer to the page 14.

Pulse button

In Standby mode, when you press the Pulse button, the product will run at full speed until the button is released again.

Or, if you press the Pulse button in Program mode or Manual mode, it will temporarily operate at the full speed. You can

return to the original speed by releasing the pulse button.

Setting button

You can save the desired programs to each of the five program buttons via Setting button. Press the Setting button for

two seconds to switch the device to Self-setting program saving mode. For more information about Self-setting program,

please refer to the page 14.

Operating your GUSTO

Connect the device to a power socket with correct electric specification. Make sure that the power of the device is

connected to the correct electric power socket. Make sure that the power plug is properly inserted into the power

socket. Switch the ON/OFF button to the ON position [14]

Start-up

In order to use the device, it is necessary to place the container on the motor block properly. Without the container the

device will not start. If you put the container on the motor block, you will hear a long beep and the display as well as the

buttons light up briefly. Now your device is in Standby mode.

Standby Mode

In Standby mode, all program icons will light up and the display shows“00:00”sign. When you see the sign it means

that the device is ready for operation. Now, you can use the Manual mode or the default programs or the Self-setting

programs of the device.

Energy Saving Mode

When the product is not used for 3 minutes, it automatically turns from Standby mode to Energy saving mode. The

display shows“OFF”and On/Off button lights up in red. To return the device for Standby mode, press the On/Off button

one time.

1Power consumption in standby mode less than 0.5 watts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bianco di puro Gusto Alpha Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bianco di puro Gusto Alpha

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info