Bedienungsanleitung Bissel 2009 - StainPro 6 (Seite 7 von 11) (Englisch)

716412

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

www.BISSELL.com

Operations

Before you clean

1. Plan activities to give your carpet time to

dry.

2. Move furniture to another area if cleaning

an entire room (optional).

3. Vacuum area with a dry vacuum cleaner

before deep cleaning.

4. Plan your cleaning route to leave an

exit path. It is best to begin cleaning in the

corner farthest from your exit.

C-1 Filling the 2-in-1 water tank

1. Remove tank from base of machine by

lifting tank carry handle. Carry like a bucket

to the sink.

2. Pull upward on bottom edge of latch in the

back of tank to unhook and remove lid.

3. Pull up on bladder fill cover that says

“Fill Here”. Fill the bladder with hand hot

(60°C/140°F MAX) tap water. Do not boil

or microwave water as it can destroy the

bladder.

4. Using measuring cup provided, fill to

indicated fill line on measuring cup and pour

in to bladder.

NOTE: Always use genuine BISSELL 2X

formulas to maximize cleaning and for the

safety of your machine.

5. Push down on bladder fill cover to close.

6. Replace top lid back onto tank by

matching lid and tank edges, then lock latch

in place.

NOTE: Remember to secure lid and test to

make sure it is secure before picking up

tank.

7. Place tank into machine base, seating

firmly in place.

C-2 Carpet cleaning

1. Plug into a proper outlet.

2. Set ReadyTools dial to Floor Cleaning

setting.

3. Turn power on by pressing red power

pedal

on back of machine with your foot.

4. With your foot, press gray recline pedal

located on back of machine next to red

power pedal.

5. While pressing spray trigger, make one

slow forward wet pass and another back.

Caution: do not overwet.

6. Release spray trigger and make one slow

forward and backward pass over same area.

7. Repeat cleaning passes until solution

being suctioned up appears clean. Continue

passes without pressing spray trigger

until you can’t see any more water being

suctioned up. Repeated passes will help aid

in dry time.

NOTE: You may notice hair and debris

deposits on the carpet or in the tank that

were loosened by the cleaning action. This

debris should be picked up and thrown

away.

C-3 Area rug cleaning

Important! Please check manufacturer’s tag

before cleaning area rugs for any specialized

cleaning instructions. We do not recommend

deep cleaning delicate, silk, wool, antique or

area rugs without a manufacturer’s tag.

When cleaning area rugs, place the rug on a

sealed surface and test a small, inconspicuous

area for colorfastness. Your carpet cleaner

should not be used on unsealed surfaces.

Follow carpet cleaning instruction in section

C-2. Keep the foot of the cleaner perpendic-

ular to the rug’s edge with each cleaning pass

to prevent damage.

ATTENTION

Some Berber carpets have a tendency to fuzz with wear.

Repeated strokes in the same area with an ordinary vacuum

or deep cleaner may aggravate this condition.

Take care not to run over loose objects or edges

of area rugs. Stalling the brush may result in

premature belt failure.

Rotating brush inside-to avoid the risk of injury-

unplug before removing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bissel 2009 - StainPro 6 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info