Bedienungsanleitung Bissel 2009 - StainPro 6 (Seite 9 von 11) (Englisch)

716412

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

www.BISSELL.com

Care,

Maintenance & Storage

D-1 Machine care

For best results, a few simple steps can

assure your machine is well maintained after

cleaning is complete.

1. Flush your machine of any remaining

residual solution.

a. Fill 2-in-1 water tank with clean hand

hot (60°C/140°F MAX) tap water and

place back on machine.

b. Press power pedal on and fully

recline handle. Press spray trigger for

15 seconds while making forward and

backward passes on the carpet. Release

spray trigger and make forward and

backward passes for another 15 seconds

or until there is no more water being

suctioned up from carpet.

2. Press power pedal

off. Unplug machine

and wrap power cord.

3. After emptying 2-in-1 water tank, rinse it

with running hand hot (60°C/140°F MAX)

tap water, taking care to clean underneath

and around heavy duty bladder. Clean

out red lint screen prior to replacing

tank. Removable nozzle may be rinsed if

necessary.

4. Replace 2-in-1 water tank on machine.

5. Any loose hair or debris can be pulled

from brush roll and thrown away. See

instructions in section D-3 to remove brush

roll.

6. Clean the ReadyTools dial assembly area

by following the instructions in steps 15-18 in

section C-5.

7. To clean attachments, remove from hose

and rinse under clean, running water. Dry

before storing. Clean hose by suctioning

clean water from tap (taking care not to let

tank overflow). Before wrapping back on

machine, lift end of hose and stretch out to

ensure all water is cleared from hose. Refer

to section C-5, illustrations 11 and 12.

8. Wipe machine’s exterior with a soft cloth.

9. After carpet is dry, you may wish to

vacuum again to remove any leftover hair

and fuzz the deep cleaner may have brought

to the carpet surface.

D-2 Machine storage

Put the unit away in a closet or basement for

the next use. Store cleaner in a protected,

dry area. Since this product uses water, it

must not be stored where there is a danger

of freezing. Freezing will damage internal

components and void the guarantee.

D-3 Brush belt and brush

removal & replacement

Occasional replacement of the brush belt

or brush may become necessary. If needed,

please follow instructions below.

1. Turn off machine and unplug it from outlet.

Wrap hose and cord on racks.

2. Remove 2-in-1 water tank and set aside.

3. IMPORTANT: Fully recline handle and

turn unit upside down.

4. Locate guard wire and remove screw.

NOTE: Guard wire does not remove.

5. Locate red belt access door and remove

two screws.

NOTE: The dark screw is a long machine

screw and will take approximately 25 full

turns to completely remove. The head of

the screw will lift from the belt access door

so that it can be easily removed.

6. Remove belt access door assembly from

end of brush and set aside.

7. Remove brush belt. If worn or damaged,

replace with new brush belt.

8. If necessary, the brush roll can be removed

for cleaning or replacement. To remove,

rotate the brush out of brush housing and

pull brush off axle attached to remaining end

cap. The remaining pivot arm can be removed

by removing the screw (this will allow for

full access to brush chamber for cleaning).

Make sure “keyed” end of metal rod is aligned

with slot in pivot arm before re-assembling.

Replace brush on axle, cogged-side, last. You

may need to rotate brush to allow it to slide

all the way down the axle.

9. Reattach brush belt by installing onto

toothed pump pulley and then onto toothed

end of brush.

10. Reattach belt access door assembly to

end of brush and rotate back into place.

Replace screws.

11. Replace screw on guard wire.

NOTE: Do not over tighten screws.

If you have any questions or are having

trouble removing, replacing or reinstalling

your brush belt or brush, please call BISSELL

Consumer Care.

To reduce the risk of electric shock, turn power

switch off and disconnect plug from electrical

outlet before performing maintenance or

troubleshooting checks.

Do not store unit where freezing may occur.

Damage to internal components may result.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bissel 2009 - StainPro 6 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info