into,
inflator or its attachments.
Do not operate the inflator when the engine is•
running.
Operate only with the accessories included or •
those rated for 8.27 bar/120 psi or higher
us
with this tool could be hazardous.
Do not play with the tool.•
dangerous.
others.
Th•
the inflator to cool for 30 minutes before storing
away
Never carry the infla•
Do•
bystanders.
Store the inflator out of reach of small children.•
The gauge is intended as a guide only•
pr
certified gauge.
Before use,•
signs of damage, ageing and wear
Do not use the appliance if the power supply cord•
or
applicable).
Electric Safety
If
by
Se
to avoid damage or injur
by an equally qualified person,
Black & Decker
Labels on tools
The following pictograms are shown on the tool:
Features
Area light1.
Pressure gauge2.
Storage location for air hose and 12 V3.
Air hose with universal valve adaptor4.
On/off switch5.
12 6.
Area light on/off switch7.
Use
Air hose and cord storage (fig.
W
t
location (3).
Fitting the accessories (fig.
Y
a
base of the unit (fig.
T•
that the lever is in the up position.
Pl•
inflation needle or tapered nozzle (fig. B).
Press the lever on the valve adapter down to lock•
it in place.
Pl•
the item to be inflated.
Note: Al
position when not in use.
Op
adaptor or with the included nozzles.
Note: Make sure that the universal valve adaptor is
firmly locked in place before turning the Inflator on.
Ma
air loss during inflation. Unless this flap is displaced
by
nozzle firmly into the valve to make sure that you push
this flap out of the way
St
no
slots located on the bottom of the Inflator (fig. C).
Warning! E
hazardous risk of bursting or personal injury
manufacturer’
being inflated.
No
is
is
re-use.
Operating the inflator
Warning! Do not operate the inflator when the car
engine is running.
Note:
is
on
accessory position.
T
Always fully extend the 12 Vdc cord before each •
use.
Co•
12
T•
se
pressure valve.
Setting the required pressure (fig.
Warning! Do not leave the inflator running
unattended. It could burst tires or other items.
Note:
before the unit will operate.
T•
ba
the required units are displayed.
Press and hold button 8 or 9 for 3 seconds until •
the display flashes.
While the display is flashing press the - or + •
bu
displayed.
Af•
to a reading of
Co•
accessories,
in
adaptor is in the down position to lock it in place.
T•
to the I position.
When the item to be inflated has reached the•
preset value the unit will automatically turn off.
T•
position.
Re•
inflated item and the 12 V
your vehicle’
Note:
vehicles 12
be lost and will need to be re-entered following the
instructions under the heading
pressure.
Operating the area light
T•
12
12
Note: Ma
is
on
accessory position.
T•
off switch (7) located on the side of the unit to
the I position.
T•
off switch (7) located on the side of the unit to
the 0 position.
T
Warning! Make sure that the 12
connected before starting this procedure.
Remove the screw (10) from the top of the lens cover•
(12).
P•
access to the bulb (13).
T•
R•
wattage (12V/5W).
Fit the lens cover (12) and secure with the screw (10).•
Using your inflator as a pressure gauge
Make sure that the unit is powered as described•
in the section
Co•
accessories if required to the item to be inflated
ma
in the down position to lock it in place.
The display will now show the actual pressure•
value in the item.
Maintenance
Y
ha
ti
ENGLISH ENGLISH
Warning!
must read the instruction manual.
Do not expose the appliance to rain or high
humidity
Before performing maintenance or cleaning on
the appliance, unplug the supply cord.
Do not leave the inflator unattended.
