Bedienungsanleitung Black Decker BDCR18 (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709546

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

Fitting the saw blade (g. A)

u Hold the tool away from the body.

u Open the blade clamp release lever (4) to the full open

position.

u Insert blade shank from the front.

u Close blade clamp release lever (4). Check to make sure

the blade (5) is clamped securley.

Note: The blade can be installed with the teeth up to assist in

ush cutting (g. G).

Removing the saw blade

Warning! Do not touch the blade immediately after use. Used

saw blades may be hot.

u Open the blade clamp release lever (4) to the full open

position.

u Remove the blade.

Lock-off button

The tool is equipped with a switch lock-off feature to prevent

unintentional operation.

u To switch the tool on, press the lock-off button (2) then

squeeze the on/off switch (1).

u Releasing the on/off switch (1) turns the tool off.

Fitting and removing the battery (g. B & C)

u To t the battery (6), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place (g. B).

u To remove the battery (6), push the battery release button

(7) while at the same time pulling the battery out of the

receptacle on the tool (g. C).

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (Fig. D)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient tempera-

tures below 10

C or above 40

C. Recommended charging

temperature: approx. 24

Note: The charger will not charge a battery if the cell

temperature is below approximately 10

C or above 40

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (6), insert it into the charger (10).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The green charging indicator will ash.

The charge is complete when the green charging indicator

switches to continuously on. The charger and the battery can

be left connected indenitely. The green charging indicator will

ash as the charger occasionally tops up the battery charge.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

green charging indicator glowing indenitely. The charger will

keep the battery pack fresh and fully charged.

Switching on and off

u To switch the tool on, press the lock-off button (2) then

squeeze the on/off switch (1).

u To switch the tool off, release the on/off switch (1).

Sawing (g. E)

u Always hold the tool with both hands (g. E).

u Let the blade (5) run freely for a few seconds before start-

ing the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u If possible, work with the shoe (3) pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being dam-

aged.

Hints for optimum use

Sawing wood (g. F)

u Clamp the workpiece securely and remove all nails and

metal objects.

u Holding the tool with both hands, work with the shoe (3)

pressed against the workpiece.

Flush cutting (g. G)

The compact design of the reciprocating saw motor housing

and pivoting shoe (3) permit close cutting to oors, corners

and other difcult areas.

To maximize ush cutting capabilities:

u Insert the blade shaft into the blade clamp with the teeth of

the blade facing up.

u Adjust the angle of the handle on the tool so you are as

close to the work surface as possible.

Sawing metal (g. H)

u Use a saw blade suitable for sawing metal. Use a ne-

tooth saw blade for ferrous metals and a coarser saw

blade for non-ferrous metals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDCR18 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info