Bedienungsanleitung Black Decker BDPR400 T1 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578621

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

(Original instructions)

Attaching the roller head (g. B)

u Slide the handle assembly (12) into the roller head (7) en-

suring that the O-ring (13) is seated inside the roller head

(7) and the black collar (14) meets the roller head (7).

u Thread the black collar (14) onto the threads of the roller

head (7) and tighten.

Attaching a roller to the roller head (g. C)

u Lubricate the tips (15) at either end of the roller frame (16)

using petroleum jelly.

u Slide the assembled roller (8) onto the roller frame (16).

Note: Make sure the roller assembly snaps into the locking

clip on the outer end cap of the roller.

Attaching the drip tray (g. D)

The drip tray helps reduce spatter and drips when painting,

especially on ceilings.

u Clip the drip tray (9) onto the roller frame (16) so that it ts

around the roller (8).

u Rotate the drip tray to the required position.

Note: The drip tray is also helpful to prevent dripping when the

Speedy Roller

is resting on the kickstand and is not in use.

Position the drip tray under the roller.

Use

Filling with paint (g. E & F)

Note: When using the Speedy Roller

for the rst application,

it will take most of the paint in the paint reservoir to saturate

the roller cover. A second ll may be needed.

u Insert the small end of the ll tube (17) through the hole in

the bottom side of the paint can clip (18). Push gently until

it click into place.

u Place the paint can clip (18) over the edge of your paint

can.

Note: For deeper containers, t a section of 19mm inner

diameter clear tubing over the ribs of the ll tube to extend it

and clip to side of pail with ll tube can clip. Cut the bottom

end of the tubing at a slight angle. Tubing is available at most

DIY stores.

u Lubricate the top of the ll tube (17) with a small amount

of petroleum jelly.

u Hold the Speedy Roller

at a 45

angle and place the ll

valve (5) over the ll tube (17). Gently push the Speedy

Roller

down so it completely covers the ll tube.

Note: Make sure the orange ll cap cover (19) is com-

pletely covered by the shroud of the can clip.

u Very rmly pull the plunger (1) all the way back to draw

paint into Speedy Roller

ensuring you apply sufcient

pressure to maintain an adequate union between the ll

valve and ll tube.

u Lift the Speedy Roller

slowly off the ll tube.

Note: If you do not receive a complete ll the rst time, push

the plunger slowly to return paint to can and then pull the back

plunger making sure the angle is correct and the orange ll

cap cover is fully seated.

Adjusting the angle of the roller head (g. G & H)

The roller head can be adjusted to three different angles.

u Press and hold the orange head ratation button (6) on the

roller head (7).

u Rotate the rollerhead (7) to the required angle.

Note: Use straight on for general painting and 40

or 80

angles for hard to reach places or when painting close to

ceiling or edging.

Note: The handle (10) can be rotated to make it more comfort-

able when painting with an angled roller frame. To rotate

handle to desired position, loosen collar (11), adjust handle

and retighten collar (g H).

Painting with the Speedy Roller

(g. I & J)

u Begin rolling on wall and push plunger handle (1) or

squeeze trigger (2) to feed paint into the roller cover.

Note: Initial saturation of the roller may require the full amount

of paint from the rst ll. Fill Speedy Roller

as needed.

Helpful hints

u The trigger only needs to be squeezed when paint is

needed.

u If you are getting a dot pattern when painting, apply more

paint.

u If the roller is sliding on the surface, apply less paint.

u You may notice petroleum jelly within the handle. This is

necessary and will help in its operation and will not affect

the paint.

u When not in use, rest the Speedy Roller

on the kick-

stand (4) with the drip tray (9) attached and positioned

under the roller..

Returning excess paint to paint tin (g. K - M)

u Place thumb over orange ll cap cover (19).

u Pull plunger (1) back to draw excess paint from roller

frame into tube.

u Hold the Speedy Roller

at a 45

angle and place the ll

valve (5) over the ll tube (17). Gently push the Speedy

Roller

down so it completely covers the ll tube.

Note: Make sure the orange ll cap cover (19) is com-

pletely covered by the shroud of the can clip.

u Push the plunger all of the way into the tube.

u Remove the roller (8) by grasping the outer end cap (20)

and the roller frame (16) and using your thumb on the

opposite hand to push the roller off

Note: Wear disposable gloves or use a plastic bag over roller

to keep your hands clean.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDPR400 T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDPR400 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info