Bedienungsanleitung Black Decker BDPR400 T1 (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578621

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

(Original instructions)

u Scrape any excess paint into the tin from the roller.

u Remove the inner end cap by inserting the metal tube of

the roller frame into the cap about 2-3 centimetres and at

an angle.

u Pull the roller frame gently towards you.

u Remove the roller core.

u Empty any remaining paint.

u Remove the outer cap (20) by inserting the roller frame

into the roller and gently pushing the cap off.

Hints for optimum use

u Only use a perforated Black & DeckerSpeedy Roller

roller cover (Accessory number : BDPRA09-XJ &

BDPRA18-XJ). Standard roller covers will not work.

u Inspect the roller cover for lint before painting, if needed

wash and dry before using.

u When using the Speedy Roller

for the rst application, it

will take most of the paint in the Speedy Roller

tube to

saturate the roller cover. A second ll may be needed.

u Keep the roller moving while pushing the plunger in or

squeezing the trigger to prevent dripping.

u Stop pushing the plunger in or squeezing trigger if the

roller starts to skid, slide or drip.

u When painting in tight areas partially ll the Speedy

Roller

or pivot the frame. This reduces its overall length.

u When leaving the Speedy Roller

unattended for a longer

period of time, wrap the roller in a plastic bag to prevent

drying, removing as much air as possible from bag.

u Make sure the type of paint you use can be cleaned with

either mineral spirits (for oil-based paints) or a warm water

and soap solution (for water soluble paints)

u Use suitable coverings to protect your oors and anything

else in the room that you do not want accidentally splat-

tered with paint.

u When using the kickstand, always pivot the head to the

straight position and release pressure by pulling the

plunger out slightly.

Maintenance and cleaning

Cleaning the Speedy Roller

(g. O - T)

u Remove the roller sleve.

u Push the ll tube directly into the ll valve. When cleaning

water soluble paints, submerge the ll tube into warm,

soapy water and pull the plunger in and out 5 or more

times. When using oil based paints, instead of water, use

proper cleaning solvent listed on manufacturers container

and dispose of properly.

Note: Use a sink, a wash tub, or any container that will hold

water to perform above ushing process. Replace water when

dirty or when moving to the next step.

u Remove the ll tube. Then submerge the roller frame, and

ensuring the ll valve is also under water, pull the plunger

in and out 5 or more times (g. P).

Note: When using a small container, pivot the roller frame to

the 80 degree position to t inside container (g. Q).

u Remove roller frame and continue cleaning as needed.

Submerge the handle in the warm, soapy water and pull

the plunger in and out 5 or more times.

Note: Wipe off remaining paint from the end of plunger (1).

u Unthread valve cap (19) and remove wiper seal (22) and

duck bill valve (21) to clean. Rinse all remaining parts and

drain all uid from the Speedy Roller

(g. S).

u Remove tubing from frame (if needed) by pinching hose

clamps. Flush frame and tubing. Replace tubing and

secure with hose clamps (24) (g. T).

Note: Always purchase a perforated Black & DeckerSpeedy

Roller

roller cover (Accessory number : BDPRA09-XJ &

BDPRA18-XJ). A standard roller will not work.

Lubricating the Speedy Roller

(g. U - X)

Lubrication helps with normal operation and should be done

after cleaning and before each use.

u Turn the threaded assembly collar (11) near the trigger

counterclockwise until the main tube assembly slides off.

Note: When reassembling, the orange threaded collar (11)

should be towards trigger handle.

u Apply petroleum jelly around and in between the rubber

seals (25). Reassemble making sure the rubber seals are

not twisted or damaged. Tighten the locking collar.

u Apply petroleum jelly to the duck bill valve (21) and wiper

seal (22) and replace within unit threading the valve cap

(19) back into place.

u Apply petroleum jelly to the inner seals on the end caps

(26) then assemble the roller by placing the core (27)

inside of roller cover (28) and attaching end caps and as

shown.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environ-

mental pollution and reduces the demand for raw

materials.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDPR400 T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDPR400 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info