Bedienungsanleitung Black Decker BDV040 T1 (Seite 5 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581361

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Use

Charging the unit (fig. A)

Note: This unit is shipped in a partially charged state.

X Charge the unit before first use using the mains

charging adaptor (9) for 60 hours or until the green

battery status LED (13) lights.

X Charge after each use until the green battery status

LED (13) lights.

Note: We recommend that this unit is re-charged every

2 months irrespective of use.

To check the battery charge status at any time, turn the unit

on by pressing the on/off button (3). The unit will beep once

and the red power LED (11) and the battery status LED (13)

will light.

The battery status LED (13) displays the level of charge:

X If the battery status LED (13) lights red charge the unit.

X If the battery status LED (13) lights green the unit is fully

charged.

Charging the unit with the mains charger (fig. A)

Make sure that the LED area light is turned off while the unit

is being charged.

X Turn the unit on by pressing the on/off button (3). The

unit will beep once and the red power LED (11) and the

battery status LED (13) will light.

X Connect the mains charging adaptor (9) into the 12 Vdc

charging socket (7) on the top of the unit.

X Insert the mains charging adaptor (9) into a mains

power socket.

X Press the recharge unit button (5). The unit will beep

once and the battery status LED (13) will flash,

indicating that the unit is charging.

Warning! The unit will beep continuously if no charging lead

is connected.

X Charge until the green battery status LED (13) lights

continuously.

X When charging is complete, disconnect the mains

charging adaptor (9) and store in a safe place.

Charging the unit with the 12 Vdc vehicle adaptor

(fig. A & B)

Note: The unit cannot be recharged while the 12 Vdc

accessory outlet (2) is in use or while the unit is being used

to boost/start a vehicle.

X Turn the unit on by pressing the on/off button (3). The

unit will beep once and the red power LED (11) and the

battery status LED (13) will light.

X Remove the 12 Vdc vehicle adaptor (10) from the

storage compartment (1) and plug it into the vehicle’s 12

Vdc accessory outlet.

X Press the recharge unit button (5). The unit will beep

once and the battery status LED (13) will flash,

indicating that the unit is charging.

X Charge until the green battery status LED (13) lights

continuously.

X When charging is complete, disconnect the 12 Vdc

vehicle adaptor (10) and return it to the storage

compartment (1).

Standby mode (fig. A)

When the unit is in standby mode (not connected to a vehicle

and not charging, but with the power on), the battery status

LED (13) will light green to indicate it is ready for use. If the

battery status LED (13) lights red, the unit needs to be

charged.

If the unit is left in standby mode for more than 3 minutes the

unit will automatically shut down. This is to prolong battery

life.

X Press the main on/off button (3) to re-activate the unit.

Using the battery booster (fig. A)

Warning! Make sure the unit is disconnected from all

charging power sources before beginning the battery

boosting procedure.

Warning! This power system is to be used only on vehicles

with dc battery systems.

Warning! Vehicles that have on-board computerized

systems may be damaged if the vehicle battery is boosted.

Before battery boosting this type of vehicle, read the vehicle

owner’s manual to confirm that external-starting assistance

is advised.

Warning! Excessive engine cranking can damage the

vehicle‘s starter motor. If the engine fails to start after the

recommended number of attempts (refer to the vehicle’s

owner manual), discontinue the battery boost procedure and

look for other problems that need to be corrected.

Warning! You MUST turn off the offending items that

discharged your battery, i.e. lights/radio etc. before you start

this procedure.

X Once offending items are turned off, allow your battery

to recover for 2-3 minutes.

X Turn the unit on by pressing the on/off button (3). The

unit will beep once and the red power LED (11) and the

battery status LED (13) will light to indicate that it is

functioning.

X Remove the 12 Vdc vehicle charging adaptor (10) from

the storage compartment (1) and plug it into the

vehicle’s 12 Vdc accessory outlet.

X Press the vehicle boost button (4). The unit will beep

once and the green vehicle boost LED (4) will flash,

indicating that the vehicle battery is being charged/

boosted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV040 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV040 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info