Bedienungsanleitung Black Decker BDV1084 (Seite 6 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53627

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

At the end of stage 2, the battery charger will automatically

begin stage 3 of the charging process.

Stage 3 - top-off charge

Stage 3 is a top-off charge. The voltage is automatically

regulated and is reduced to a predetermined level while the

current is adjusted for a safe, effective battery charge. At the

conclusion of stage 3, the appliance will beep, signalling the

completion of the charging cycle.

Function pushbuttons (fig. A)

The function pushbuttons on the control panel (3), from left

to right, are:

2/6/10A pushbutton (11) (charge rate selector

step 2). This pushbutton allows the user to select

the charge rate based on the battery size. This

selection and the actual battery charge rate are

monitored by the microprocessor. The battery

charger will stop charging if the rate is too fast or

too slow for the battery size or condition.

Battery voltage pushbutton (10). This

pushbutton enables a check to measure the

battery voltage.

Alternator check pushbutton (9). This

pushbutton enables a five-second check that

measures the battery voltage. This check is

repeated at various electrical load levels and the

tests allow the user to determine if the alternator

can keep up with the loads. It can indicate

whether an alternator service may be required.

Control panel LEDs (fig. A)

The following icons are shown on your battery charger:

Fault LED (5). Lights when any of several faults

are detected, see F01 through F05 Codes as

described in the "Troubleshooting" section, later

in this manual.

Reverse polarity LED (6) - lights when the

battery clamps (4) are incorrectly connected to

the battery terminals.

Battery voltage LED (7) - lights when the

battery voltage pushbutton (10) is pressed.

Alternator good LED (8) - lights when load or

no load checks show that the alternator is

keeping up with the electrical load.

Charge rate selection (fig. A)

X This appliance has three charge rate settings, accessed by

the 2/6/10A pushbutton (11):

- 2 amps: smaller batteries, as in lawn mowers,

motorcycles, etc.

- 6 amps: mid-sized batteries, as in small cars.

- 10 amps: automobiles and light trucks.

X After the battery clamps (4) are correctly connected, plug in

the battery charger to a 230 Vac outlet. The battery charger

will show a circulating pattern on the digital display (2), to

indicate that power has been applied. Select the proper

charge current rate based on battery size.

Charging the battery (fig. A)

X Press the 2/6/10A pushbutton (11), the appliance sounds a

beep and displays the charging current. The battery charger

starts charging at 2 amps automatically if the 2/6/10A

pushbutton (11) is not pressed within 3 minutes after

applying AC power.

X The battery charger will occasionally sound a beep and

display 0.0 during self-test or during the charging stage

changes.

X Pressing the 2/6/10A pushbutton (11) again will advance

the charge rate to 6 A, and again to 10 A. Pressing the

pushbutton (11) again will turn OFF the battery charger

output and the digital display (2) will show 000.

Note: This selection and the actual battery charge rate are

monitored by the microprocessor and the unit will stop

charging if the selected rate is too fast or too slow for battery

size or condition.

X As the battery nears full charge capacity, the unit's output

will automatically drop to a lower charge rate.

X The digital display (2) shows the charge current. To view

the battery voltage, press the battery voltage pushbutton

(10). The battery charger will sound a beep and display the

the battery voltage.

X Press the battery voltage pushbutton (10) again to display

the charge current.

X The digital display (2) shows FUL when the battery is fully

charged.

X Disconnect the ac power cord first, then the negative

clamp, and finally the positive clamp.

Automatic float charging (fig. A)

The automatic float charge feature is ideal for maintaining a

battery. It automatically tops off the battery as required to

keep the battery fully charged all the time.

X Keep the ac power and battery connected when the battery

has been fully charged.

X The battery charger monitors the battery and tops it off as

needed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV1084 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV1084

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info