Bedienungsanleitung Black Decker BDV1085 (Seite 6 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53629

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

Stage 3 - top-off charge (fig. C)

Stage 3 is a top-off charge. The voltage is automatically

regulated and is reduced to a predetermined level while the

current is adjusted for a safe, effective battery charge. At the

conclusion of stage 3, the appliance will beep, signalling the

completion of the charging cycle.

Controls and Indicators

Function pushbuttons (fig. A)

The function pushbuttons, from left to right, are:

Battery type pushbutton (16) (Step 1). This

pushbutton allows the user to select wet or

maintenance-free type of battery for efficient

and safe charge. Most automotive batteries are

wet batteries. Refer to the battery

manufacturer's specifications for the battery

type.

2/10/30A pushbutton (15) (charge rate

selector step 2). This pushbutton allows the

user to select the charge rate based on battery

size. This selection and the actual battery charge

rate are monitored by the microprocessor and

displayed on the digital display (1). The battery

charger will stop charging if the rate is too fast or

too slow for the battery size or condition.

80 A pushbutton (12) (engine start). This

pushbutton places the battery charger in an

engine start sequence. This pushbutton will not

be activated unless the battery charger is in the

30 A charge mode. Set the 2/10/30A pushbutton

(15) to 30 A first to activate this pushbutton.

Alternator check pushbutton (13). This

pushbutton enables a five-second check that

measures the battery voltage. This check is

repeated at various electrical load levels and the

tests allow the user to determine if the alternator

can keep up with the loads. It can indicate

whether an alternator service may be required.

Battery voltage pushbutton (14). This

pushbutton enables a check to measure the

battery voltage.

Equalize pushbutton (9). This is a recessed

pushbutton used to start the equalize process.

Control panel LEDs (fig. A)

WET LED (10) - lights when the battery type

selector is on wet battery type

Maintenance free LED (11) - lights when the

battery type selector is on maintenance free

battery type.

Float charge LED (6) - lights when the

automatic charge monitoring is active. This

feature allows a battery to maintain its charge

over long periods of non-use. If there is any loss

of power to the battery charger, the battery

charger will automatically return to the default

settings once power is restored. Battery selector

type would be maintenance free.

Battery voltage LED (7) - lights when the

battery voltage is displayed on the digital display

(1).

Alternator good LED (8) - lights when load or

no load checks show that the alternator is

keeping up with the electrical load.

Charge rate selection (fig. A)

X After the battery clamps (5) are correctly connected, plug in

the battery charger to a 230 Vac outlet. The battery charger

will show a circulating pattern on the digital display (1), to

indicate that power has been applied. Select the proper

charge current rate based on battery size.

Charging the battery (fig. A)

X Press the battery type pushbutton (16) until the required

battery type LED lights (10) or (11).

Note: The default selection is the maintenance free type

battery (11).

X Press the 2/10/30A pushbutton (15) to begin charging at

the 2 A rate; the appliance sounds a beep and displays the

charging current. The battery charger starts charging at the

2 A rate automatically if the 2/10/30A pushbutton (15) is

not pressed within 3 minutes after applying ac power.

X If the digital display (1) on the battery charger varies

between F03 and the Amp rate, the battery is sulphated

and the battery charger is trying to give it some charge. If

after approximately 3 hours the digital display (1) just

shows F03, then the battery will not charge.

X The battery charger occasionally sounds a beep and

displays 0.0 during self-test or charging stage changes.

This is normal.

X Pressing the 2/10/30A pushbutton (15) again advances the

charging rate to 10 A, and pressing the pushbutton once

more advances the charging rate to 30 A. (Pressing the

pushbutton again will turn OFF the battery charger output

and the digital display (1) will show 000).

Note: This selection and the actual battery charge rate are

monitored by the microprocessor, and the appliance will stop

charging if the selected rate is too fast or too slow for battery

size or condition.

80A

WET

GEL/AGM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV1085 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV1085

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info