Bedienungsanleitung Black Decker BDV1085 (Seite 7 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53629

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

X As the battery nears full charge capacity, the appliance's

output will automatically drop to a lower charge rate.

X Pressing the 2/10/30A (15) button repeatedly advances to

stand-by mode; the appliance sounds a beep, displays 000

and stops charging.

X The battery charger displays the charge current.

X To view the battery voltage, press the battery voltage

pushbutton (14). The charger will sound a beep and display

the battery voltage. Press the battery voltage pushbutton

(14) again to return to displaying the charge current.

X The digital display (1) shows FUL when the battery is fully

charged.

X Disconnect the ac power cord first, then the negative

clamp, and finally the positive clamp.

Automatic float charging (fig. A)

The automatic float charge feature is ideal for maintaining a

battery. It automatically tops off the battery as required to

keep the battery fully charged all the time.

X Keep the ac power and battery connected when the battery

has been fully charged.

X The charger monitors the battery and tops it off as needed.

X The float charge LED (6) lights and the digital display (1)

shows the charge current when topping off the battery and

returns to FUL when completed.

X To view the battery voltage, press the battery voltage

pushbutton (14).

Warning! If the battery size is not known, charge at the 2 A

rate. DO NOT overcharge batteries.

Equalizing (fig. A)

Equalizing is the process by which the fluid in each of a

battery's cells is equalized.

This process occurs after charging is complete.

Warning! Never try to equalize a maintenance free type

battery. The resulting explosion could cause property damage,

serious injury and/or death.

X Remove or disconnect the vehicle's battery when

equalizing.

The frequency which the equalization process needs to be

run depends on the use of the battery. The more the battery

is used, the more undercharged it becomes; thus the more

frequently the battery should be equalized.

Do not use this mode on sealed or valve regulated batteries.

This mode is only meant for wet (unsealed/vented) batteries.

X Make sure that there are no flammable sources near the

recharging site.

X Wear safety glasses, gloves and protective clothing.

X Remove the battery from the vehicle. Make sure that the

battery has good ventilation. The process causes the

release of hydrogen and oxygen. An accumulation of these

gases presents a real danger of explosion.

X Open the battery cap, if removable.

X Fill the battery with distilled water according to the

manufacturer's instructions. Since batteries may rapidly

bubble while being charged, remember to refill (only with

distilled water) after the equalization process is complete

and the voltage is back to normal.

X Follow the steps in the "Charging the battery" section.

X Push the battery type pushbutton (16) until WET is

displayed (this mode will only work if a WET battery is

selected).

X Choose the correct charge rate and start charging. You can

check the battery voltage by pushing the battery voltage

pushbutton (14). This will trigger the battery voltage

LED (7).

X Push the equalize pushbutton (9) at any time and the

battery will automatically begin to equalize in 4 A limited

current.

Note: To push the recessed pushbutton you will need a

small pin or a ballpoint pen.

X Check the temperature every hour by touching the battery.

If the battery is hot to the touch, stop the charging and

allow the battery to cool.

The voltage rises to between 15.3 V to 16.2 V (2.55 to 2.7 V

per cell) depending on the ambient temperature, it will

automatically adjust.

The WET LED (10) flashes while the battery charger is in

equalize mode.

The digital display(1) will show FUL when the equalization

process is complete.

Engine start (fig. A)

The engine start function can supply 80 A for engine starting.

X Set the 2/10/30A pushbutton (15) to the 30 A mode and

immediately press the 80A pushbutton (12) to activate the

engine start mode.

The digital display (1) will countdown from 999 to 000.

When a count of 000 is reached and the digital display (1)

begins to flash, the vehicle is ready to start.

X Turn over the engine using the manufacturer's guidelines,

typically in 3 to 5 second bursts.

The high current engine starting function requires a resting/

cooling period between tries. The battery charger will switch

back to regular charge mode after 5 seconds and will not

allow operation in the Engine Start mode for 4 minutes.

X Wait 4 to 5 minutes before a second attempt at starting the

engine, if needed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDV1085 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDV1085

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info