Bedienungsanleitung Black Decker BEMW481BH (Seite 13 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709478

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on each of the

comfort grip handles (2).

Adjusting the height of cut (g. K)

The height of cut is adjusted by the central height adjust

mechanism, there are 6 positions to choose from.

u Pull the height adjustment lever (12) away from the body

of the unit.

u Move the lever towards the rear of the appliance to

lower the height of cut.

u Move the lever towards the front of the appliance to

raise the height of cut.

u Push the height adjustment lever into one of the 6

height locations.

NOTE: The height of cut can be viewed on the height of cut

gauge (11) on the side of the unit.

Switching on and off (g. M)

Switching on

u Push the power button (1).

u Pull the left or right ON/OFF switch (3) towards the handle.

Switching off

u Release ON/OFF switches (3).

Warning! Never attempt to lock a switch in the on position.

Mowing (g. N, O1 & O2)

We recommend to use your mower as outlined in this section

in order to achieve optimum results and to reduce the risk of

cutting the mains cable.

u Loop the extension cord through the cable

management system (5) (BEMW471BH, BEMW481BH

units only) as shown (Fig. N). Ensure you

leave approximately 100mm of cord between the power

switch (1) and the cable management system.

u Ensure that the cable management system

(BEMW471BH, BEMW481BH units only) can slide

freely from one side to the other.

u Place the bulk of the mains cable on the lawn, close to the

starting point (position 1 in g. O1).

u Switch the appliance on as described above.

u Proceed as shown in g. O1

u Move from position 1 to position 2.

u Turn right and proceed towards position 3. The cable

management system will slide from one side to the other,

ensuring the extension cord is kept away from the cutting

blade.

u Turn left and move towards position 4.

u Repeat the above procedure as required.

Warning! Do not work towards the cable as shown in g. O2.

Up to edge cutting (g. P, Q)

Up to edge cutting allows you to cut grass right up to the edge

of a wall or fence (g P).

Up to edge cutting allows you to accurately cut grass right up

to the edge of your lawn (g Q).

u With the lawnmower parallel with the edge of your lawn,

push the lawnmower along the edge of the lawn. Ensure

that the edge of mower is slightly over the edge of your

lawn (g.Q).

Cable tidy (g. R)

u Cable tidy, stores cable when not in use. Only available on

BEMW471BH & BEMW481BH GB units.

Removing Blade (Fig. S, T)

Note: BEMW461BH, BEMW471BH & BEMW481BH all use

new winged blades which improves collection vs previous

range of mowers. Blade accessories Cat # 34cm A6320

38cm A6321 42cm A6322.

Warning! Ensure the blade has completely stopped

and disconnect the mower from the power source.

u Cut a piece of 2x4 wood (16) 305mm to keep blade from

turning while removing ange nut.

u Turn the appliance onto its side. Wear gloves and proper

eye protection. Be careful of sharp edges of blade.

u Position piece of wood (16) to keep blade from turning

as shown in Fig. S.

u Use a 14mm wrench (18) to loosen and remove the

blade bolt by turning counterclockwise.

u Pull off blade (17), blade insulator (19), as shown in

Fig. T. Examine all pieces for damage and replace if

necessary.

Installing Blade (Fig. U)

u Place blade insulator (19) then the blade (17) onto bolt

shaft with the lettering on the blade facing out, and place

the blade bolt (20) onto the bolt shaft.

u Tighten the blade bolt as rmly as possible by hand.

u Position piece of wood (16) to keep blade from turning

as shown in Fig. U.

u Use a 14mm wrench to securely tighten the blade

bolt by turning the wrench clockwise.

Blade sharpening

Keep blade sharp for best mower performance. A dull blade

does not cut grass cleanly. Use proper eye protection while

removing, sharpening, and installing blade. Sharpening the

blade twice during a mowing season is usually sufcient under

normal circumstances.

Sand causes the blade to dull quickly. If your lawn has sandy

soil, more frequent sharpening may be required.

Note: Replace bent or damaged blade immediately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BEMW481BH Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info