Bedienungsanleitung Black Decker BES610 (Seite 7 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709475

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Pendulum Stroke dial (g. F)

The BES610 has four cutting modes with increasing

amounts of pendulum action:

u Position 0: metal and aluminium and sheet metal (no

pendulum action).

u Position 1: for laminates, hard wood, work tops.

u Position 2: for plywood and PVC/Plastics.

u Position 3: for soft wood and fast cutting.

To adjust the pendulum action:

u Rotate the Pendulum Stroke dial (6) to the required

position.

Sawing

Hold the tool firmly with both hands while cutting.

The shoe plate (4) should be held firmly against the material

being cut. This will help prevent the saw from jumping, reduce

vibration and minimise blade breakage.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Straight assist blade (Only available with BES610K

model)

When you require a straight cut with extra precision, use the

straight assist blade (8a).

Sawing laminates

When cutting laminates, splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate is

sitting on the presentation surface either use a saw blade that

cuts on the downward stroke or:

u Use a fine-tooth saw blade.

u Saw from the back surface of the workpiece.

u To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Sawing metal

Warning! Do not use a vacuum when cutting metal. Metal

filings will be hot and may cause fire.

Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Plunge Cutting (g. H)

A plunge cut is an easy method of making an inside cut.

The saw can be inserted directly into a panel or board without

rst drilling a lead or pilot hole. In plunge cutting, measure

the surface to be cut and mark clearly with a pencil. Next tip

the saw forward until the front end of the shoe sits rmly on

the work surface and the blade clears the work through its

full stroke. Switch the tool on and allow it to attain maximum

speed.

Grip the saw rmly and lower the back edge of tool

slowly until the blade reaches its complete depth. Hold the

shoe at against the wood and begin cutting. Do not remove

blade from cut while it is still moving. Blade must come to a

complete stop.

Accessories

The performance of your tool depends on the accessory used.

BLACK+DECKER accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Warning! Before performing any maintenance on the tool,

unplug the tool before cleaning it.

u Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed

of with normal household waste.

Products and batteries contain materials that can be recov-

ered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BES610 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info