Bedienungsanleitung Black Decker BHFEV36B2D (Seite 8 von 12) (Englisch)

792731

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH (Original instructions)

To install battery pack (g. B)

uInsert battery (4) into tool until an audible click is heard as

shown in gure B.

uEnsure battery pack is fully seated and fully latched into

position.

To remove battery pack

uDepress the battery release button and pull battery pack

(4) out of the tool.

Assembly (Fig. C)

uAlign the top of the extension tube (9) with the vacuum

inlet (16) as shown in gure C.

uPush the extension tube (9) onto the vacuum inlet (16) so

it locks into position.

uAlign the bottom of the extension tube (9) with the oor

head (8) as shown in gure C.

uPush the bottom of the extension tube (9) onto the oor

head (8) so it locks into position.

uTo remove an accessory, press the accessory release

latch located on the accessory and pull it off.

USE

This vacuum cleaner can be used in one of four ways.

uWith the extension tube (9) and the oor brush (8) as

shown in gure C.

uWith the oor brush (8) and the vacuum inlet (16) as

shown in gure D.

uWith the extension tube (9) and an accesssory tool (10),

(11), (13) or (14) as shown in gure E.

uWith an accesssory tool (10), (11), (13) or (14) and the

vacuum inlet (16) as shown in gure E.

uAccessories not supplied with your unit can be ordered

through service department.

Switching ON and OFF (Fig. F)

uTo switch ON, press the On/Off button (1).

uFor increased power, slide the variable power switch (2)

forward.

Note: The oor brush (8) will power on when it is

attached to the vacuum or extension tube (it can be switched

off by pressing the button 2a on the display). The LED

worklights on the front of the oor head will illuminate

whenever the beater bar activation button (2a) is switched ON

(they can be switched off by pressing the button again).

Note: The state of charge indicator LEDs (3) will

illuminate while the vacuum is ON.

uTo switch OFF, press the On/Off button (1).

uReturn the battery to the charger immediately after use so

that it will be ready and fully charged for the next use.

Using an Accessory tool (Fig. G)

Your vacuum may come with some of the following tools.

u2 in 1 Accesssory tool (10)

uCrevice tool (11).

uPet hair tool (13).

uWide mouth dust brush (14).

uThe accessory tool (10), (11), (13) or (14) can be tted

either directly to the extension tube (6) or to the vacuum

inlet (5) as shown in Fig. G.

uAlign the top of the accessory tool (10), (11), (13) or (14)

with the vacuum inlet (16) or extension tube connection

(9a) and push into place so it locks into position as shown

in gure G.

Cleaning and emptying the vacuum

Filter agitator (Fig. H)

With the lift away dust canister (6) off the chassis (17) ,

rotate the lter agitator wheel 5 - 10 times to remove exces-

sive dust from the lter thus increasing its performance.

Note: It is recommended that you agitate when the unit is

emptied and the prelter removed.

Note: Maximum dust collection will only be obtained with

clean lters and an empty dust canister.

If dust begins to fall back out of the product after it is switched

off, this indicates that the dust canister is full and requires

emptying.

To empty the dust canister (Fig. I, J)

uLift and remove the lift away dust canister (6) from the

chassis (17) as shown in gure I.

uPlace the dust canister over a dust bin and press the

dust canister lid release button (6a) to empty the dust

canister as shown in gure J.

uClose the dust canister lid (7), until it “clicks” rmly

into position.

uInstall the lift away dust canister (6) back onto the

chassis (17).

Removing pre-lter (Fig. K)

uLift and remove the lift away dust canister (6) from the

chassis (17) as shown in gure I.

uPlace the dust canister over a trash bin and press the

dust canister lid release button (6a) to empty the dust

canister as shown in gure J.

uUse your index nger and thumb to pinch the pre-lter

(18), pull the pre-lter (18 ) from the dust canister (6) as

shown in gure K.

Note: The lter housing ts snuggly in the dust canister

and may be difcult to remove at rst.

uEmpty the dust canister.

uInstall the pre-lter (18) into the dust canister (6)

ensuring the dust canister tab (20) aligns with the prelter

slot (19) as shown in gure K.

uInstall the dust canister onto the vacuum, until it “clicks”

rmly into position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BHFEV36B2D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info