Bedienungsanleitung Black Decker CD301 T1 (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

580864

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Lock-on button

3. Dust shroud

4. Blade support roller

5. Shoe plate

6. Dust extraction opening

7. Allen key

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and

that the saw blade has stopped.

Fitting the saw blade (fig. A)

◆ Remove the dust shroud (3).

◆ Loosen the screw (8) using the Allen key provided.

◆ Hold the saw blade (9) as shown, with the teeth facing

forward.

◆ Insert the shank of the saw blade into the blade holder (10)

as far as it will go.

◆ Tighten the screw (8).

◆ Adjust the blade support roller as described below.

Adjusting the blade support roller (fig. B & C)

◆ Loosen the screws (11).

◆ Push the blade support roller (4) forward until it touches

the saw blade.

◆ Tighten the screws (11).

◆ Make sure that the shoe plate is adjusted correctly.

See below.

Connecting a vacuum cleaner to the tool (fig. D)

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool. The adaptor can be purchased from your

local Black & Decker retailer.

◆ Push the adaptor (12) into the opening (6).

◆ Connect the vacuum cleaner hose (13) to the adaptor.

◆ Make sure that the dust shroud (3) is fitted.

Use

Adjusting the shoe plate for bevel cuts (fig. E)

The shoe plate can be set to a left or right bevel angle of up to

45°.

◆ Loosen the screws (11).

◆ Pull the shoe plate (5) forward, set it to the required angle

and push it back into place. You can use the scale or a

protractor to check the angle.

◆ Tighten the screws (11).

◆ Make sure that the blade support roller is adjusted correctly.

To reset the shoe plate for straight cuts:

◆ Loosen the screws (11).

◆ Pull the shoe plate forward and set it to an angle of

approx. 0°.

◆ Make sure that the blade support roller is adjusted correctly.

◆ Push the shoe plate backward and tighten the screws (11).

◆ Use a square to check the angle.

Switching on and off

◆ To switch the tool on, press the on/off switch (1).

◆ For continuous operation, press the lock-on button (2) and

release the on/off switch.

◆ To switch the tool off, release the on/off switch.

To switch the tool off when in continuous operation, press

the on/off switch once more and release it.

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may

occur on the surface closest to the shoe plate.

◆ Use a fine-tooth saw blade.

◆ Saw from the back surface of the workpiece.

◆ To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw

through this sandwich.

Sawing metal

◆ Be aware that sawing metal takes much more time than

sawing wood.

◆ Use a saw blade suitable for sawing metal.

◆ When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

◆ Spread a film of oil along the intended line of cut.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the performance

of your tool. By using these accessories you will get the very

best from your tool.

ENGLISH

AST7EUR.PM65 19-04-2002, 12:334

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CD301 T1 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CD301 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info