Bedienungsanleitung Black Decker CLM3820 T1 (Seite 14 von 164) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

586103

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

ENGLISH

(Original instructions)

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Removing and installing the blade (g. S, T & U)

Warning! Do not touch the blade before the safety key has

been removed and the blades have come to a complete stop.

u Release the bail bar (2) to turn mower off, wait for the

blade to stop and remove the safety key (1).

u Cut a piece of wood (approximately 50 mm x 100 mm x

600 mm long) to use to keep the blade from turning while

removing the ange nut (29).

u Turn the mower on its side.

Warning! Wear gloves and proper eye protection. Be careful

of the sharp edges of the blade.

u Position the wood (28) and remove the ange nut (29)

with a 13 mm wrench (g. S).

u Remove the washer (30), blade (31), square blade guide

(32) and the fan (33) (g T). Examine the blade guide (32)

and fan (33) for damage and replace if necessary.

When tting the blade, make sure that the grass side of the

blade (Indicated by arrows on either end) will face the ground

when the mower is returned to its normal upright position.

u Install the fan (33). Be sure to position the fan blades (34)

so that they face in towards the mower.

u Install the blade guide (32). Be sure to position the 'D'

shaped pegs (35) so that they face out, away from the

mower.

u Be sure to align the ats on the on the fan (33) and the

blade guide (32) with the ats of the shaft.

u Fit the blade (31) onto the blade guide (32) with the ar-

rows facing outwards.

u Position the piece of wood (28) to keep the blade (31)

from turning (g. U).

u Install the washer (30) and ange nut (29) then tighten

with a 13mm wrench.

Blade sharpening (g. V)

Keep the blade sharp for best performance. A dull blade does

not cut grass cleanly or mulch properly.

Warning! Always make sure that the safety key is removed.

Warning! Wear proper eye protection while removing, sharp-

ening and installing a blade.

Sharpening the blade twice during a mowing season is usually

sufcient under normal circumstances. Sand causes the

blade to dull quickly. If your lawn has sandy soil more frequent

sharpening may be required.

u Replace bent or damaged blades immediately.

When sharpening the blade:

u Make sure that the blade remains balanced.

u Sharpen the blade at the original cutting angle.

u Sharpen the cutting edges on both ends of the blade,

removing equal amounts of material from both ends.

To sharpen a blade in a vice (g. V)

u Release the bail bar (2) to turn the lawnmower off and wait

for the blade to come to a complete stop.

u Remove the safety key (1) and the battery pack (22) and

turn the lawnmower on to its side.

u Remove the blade (31) from the mower, see the instruc-

tions for removing and installing blades.

Warning! Wear proper eye protection and gloves and be

careful of the sharp edges of the blade.

u Put the blade (31) in a vice.

u Carefully le the cutting edges of the blade with a ne

tooth le or a sharpening stone, maintaining the original

cutting edge.

u Check the balance of the blade, see the instructions for

blade balancing.

u Install the blade (31) on the mower and tighten securely,

see the instructions for removing and installing blades.

Blade balancing (g. W)

u Check the balance of the blade by putting the centre hole

in the blade on to a nail or a round shank screwdriver that

is clamped horizontally in a vice. If either end of the blade

rotates downward, le that end of the blade until the blade

is balanced.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require no lubrication.

Cleaning

u Release the bail bar (2) to turn the lawnmower off and wait

for the blade to come to a complete stop.

u Remove the safety key (1).

u Use only mild soap and a damp cloth to clean the mower.

u Use a blunt tool to clean out any clippings which may have

accumulated on the underside of the mower.

u After several uses, check all exposed fasteners for tight-

ness.

Preventing corrosion

Fertilisers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilisers or chemicals have been used, the mower

should be cleaned immediately afterward as follows:

u Release the bail bar (2) to turn the lawnmower off and wait

for the blade to come to a complete stop.

Black Decker CLM3820 T1 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CLM3820 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info