Bedienungsanleitung Black Decker CLMA4820L2 (Seite 12 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709483

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

ENGLISH

(Original instructions)

After this happens, the charger automatically switches to

the Pack Charging mode. This feature ensures maximum

battery life. The red LED ashes in the pattern indicated on

the label when the Hot/Cold pack delay is detected.

State of Charge Indicator

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery while in the trimmer and during charging. It does not

indicate appliance functionality and is subject to variation

based on product components, temperature and end user

application.

Checking State of Charge during use

u Press the state of charge indicator (A1).

u The four LEDs (A2) will illuminate indicating the percent

of charge in the battery (Fig.A.)

u If LED light does not illuminate, charge battery.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Features

This appliance includes some or all of the following features.

1. Switch box

2. Bail handle

3. Upper-handle

4. Lower-handle

5. Upper-handle attachment levers (2)

6. Lower-handle attachment levers (2)

7. Cut height adjust lever

8. Grass collection bag

9. Rear door cover

10. Battery port

11. Battery storage compartment

12. Carrying handles

13. EdgeMax™

Installing and removing the battery pack

(g. B - C)

u depress the battery port cover release button (14) and pull

the battery port cover (15) up to expose the battery port

(10) as shown in gure B.

u Slide the battery (16) into the battery port until it is fully

seated and an audible click is heard (gure C). Make sure

battery pack is fully seated and fully latched into position.

u Close the battery port cover. Ensure the cover is fully

latched before starting mower.

To remove battery pack (g. D)

u Open the battery port cover (15).

u Depress the battery release button (17) on the battery

pack and pull battery pack out of tool as shown in gure D.

Battery storage

An extra battery can be stored using the battery storage

compartment (11).

u Lift the storage compartment cover and slide the battery

into the compartment as shown in gure E. Battery in this

compartment will not actuate the mower.

u Screw the upper handle quick release clamps (7) through

the lower handle into the clamp nuts (20), With the

upper handle quick release clamps screwed in half way,

close the quick release clamps (g. G). If the connection

between the handle and quick release clamps is too tight

or loose, adjust the depth of the quick release clamps and

close them again until the teeth are fully closed.

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the safety key and battery have been

removed.

Attaching lower handle (g. F)

u lift lower handle (4) into place making sure the arrow (18)

on the base of the mower lines up with 1, 2, or 3 on the

base of the handle (19) (inset of gure F).

Note! Ensure each side of the lower handle is set on the

same number. The arrow must be lined up with 1, 2, or 3 for

operation.

u Close the handle height adjust levers (7) as shown in

gure F. As you close each, make sure the teeth are

engaged as shown in gure G.

u If the connection between the handle and lever is too tight

or loose, open the lever and adjust the depth of the lever

by turning the lever. Close it again until the teeth are fully

clasped and each lever stays securely closed.

Attaching upper handle (g. H)

u Remove the upper-handle attachment levers (5), nuts

(20), and washers (21) from the handle.

u Line up the holes on the bottom of the upper handle (3)

with the holes on the top of the lower handle (4).

Note: Make sure the cord is located on the front of both

handles. If it is not it may result in the cord tangling and the

inability to easily store the mower (g. I)

u From the outside of the upper handle (3), slide the lever

bolt through the holes.

u Slide the washer over the bolt of the lever and loosely

assemble the entire assembly with the nut.

u Rotate the upper handle into its operating position.

u Close the lever. If it is too tight or too loose, open the lever

and the nut to adjust the clamping. Check the levers by

closing them. They should be tight enough so the handles

are held rmly, but loose enough so the levers can be fully

closed. Adjust by opening the lever and turning the nut

until the handles are secured.

Securing the motor cable (g. J)

Warning: Attach cable so that it does not become stretched or

pinched in the joints of the handles during use or folding. This

can cause damage to the cord.

The motor cable (22) has to be xed to the handles using the

cable restraints (23) that are already attached to the handle to

clip the cable to the handle:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CLMA4820L2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info