Bedienungsanleitung Black Decker CLMA4820L2 (Seite 15 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709483

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

ENGLISH

(Original instructions)

plastic bearing surfaces which require no lubrication.

Cleaning

Release bail handle (2) to turn mower off, let the blade come

to a stop and then remove safety key. Use only mild soap

and a damp cloth to clean the mower. Clean out any clippings

which may have accumulated on the underside of the deck.

After several uses, check all exposed fasteners for tightness.

Preventing corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows: Release

bail handle (2) to turn mower off and remove safety key and

battery. Wipe all exposed parts with a damp cloth.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory opera-

tion depends upon proper tool/appliance care and regular

cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Troubleshooting

If your appliance seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local BLACK+DECKER repair agent.

Warning! Before proceeding, release the bail bar to turn

mower off, wait for the blade to stop and remove the safety

Problem Possible solution

Mower doesn’t run when

bail handle is activated.

Check to make sure safety key has been

installed and is fully seated and that button on

switch housing is being completely depressed

before pulling bail handle.

Release bail handle to turn mower off. Remove

safety key and battery pack, turn mower over

and check that blade is free to turn.

Has battery been fully charged? Plug in

charger and wait for green light to come on

Problem Possible solution

Motor stops while

mowing.

Release bail handle to turn mower off. Remove

safety key and battery pack. Turn mower over

and check that blade is free to turn.

Raise cutting height of wheels to highest posi-

tion and start mower.

Check that the battery cavity is free of debris

and is connected properly.

Has battery been fully charged? Press state of

charge button.

Avoid overloading the mower. Slow down the

cutting pace, or raise the cut height.

Mower runs but cutting

performance is unsatis-

factory, or does not cut

entire lawn.

Has battery been fully charged? Press state of

charge button.

Release bail handle to turn mower off. Remove

safety key and battery pack. Turn mower over

and check:

u Blade for sharpness - Keep blade sharp.

u Deck and discharge chute for clogging.

Wheel height adjustment may be set too low

for grass condition. Raise cutting height.

Mower is too hard to

push.

Release bail handle to turn mower off. Remove

safety key and battery pack. Raise cutting

height to reduce deck drag on grass. Check

each wheel for free rotation

Mower is abnormally

noisy and vibrates.

Release bail handle to turn mower off. Remove

safety key and battery pack. Turn mower on

side and check blade to ensure it has not been

bent or damaged. If blade is damaged, replace

with a BLACK+DECKER replacement blade.

If the underside of the deck is damaged, return

mower to a BLACK+DECKER Authorized

service center.

If there is no visible damage to the blade and

the mower still vibrates:

u Release bail handle to turn mower off.

u Remove safety key and battery pack.

u Disassemble entire blade assembly as

described in the “Removing and installing

blade” section.

u Remove any debris and clean each

piece.

u Replace each piece as described in the

“Removing and installing blade” section.

If mower still vibrates, return the mower to

an authorized BLACK+DECKER authorized

service center.

Battery charger LEDs

not on.

Check plug connection.

Replace charger.

Mower not picking up

clippings with bag.

Chute clogged. Release bail handle to turn

mower off. Remove safety key and battery

pack. Clear chute of grass clippings.

Raise cutting height of wheels to shorten

length of the cut.

Bag full. Empty bag more often.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CLMA4820L2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info